Canon W8200 User Guide - Page 147

Feed Limit, Size Undetected, Remove Ink Tank, Turn Power Off, W-Ink Full Soon, Problem 1, Solution - service manual

Get Canon W8200 - imagePROGRAF Color Inkjet Printer PDF manuals and user guides View all Canon W8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 147 highlights

Feed Limit Problem 1: You pressed on the operation panel to feed more media than allowed. Solution: Open the tray, then turn the roll holder manually to feed the extra media. Size Undetected Problem 1: The media has shifted out of the correct load position, or the media is curled. Solution: Set the media correctly. (Æ P.2-9, P.2-21) Problem 2: The printer interior is dusty or dirty. Solution: Open the upper cover and clean inside the printer. (Æ P.6-11) Remove Ink Tank Problem 1: Right cover was closed without removing the ink tank. Solution: Remove the ink tank. Turn Power Off!! Problem 1: The tape inside the upper cover or the belt stopper have not been removed. Solution: Switch the printer off, open the upper cover, remove the tape and belt stopper, then press the Power button. (Æ Setup Guide) Problem 2: The printer has malfunctioned. Solution: Switch the printer off, then press and hold down the Power button for over 3 seconds to switch the printer on again. Solution: If the message occurs again after switching the printer off and on, note the message in the first line of the operation panel display, then call for service. W-Ink Full Soon Problem 1: The waste ink tank is nearly full and requires replacing very soon. Solution: Printing can continue after this message is displayed. However, you should call for service as soon as possible before a Service Call is issued. Message Is Displayed 7-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Message Is Displayed
7-15
Feed Limit
Problem 1:
You pressed
±
on the operation panel to feed more media than allowed.
Solution:
Open the tray, then turn the roll holder manually to feed the extra media.
Size Undetected
Problem 1:
The media has shifted out of the correct load position, or the media is
curled.
Solution:
Set the media correctly. (
Æ
P.2-9, P.2-21)
Problem 2:
The printer interior is dusty or dirty.
Solution:
Open the upper cover and clean inside the printer. (
Æ
P.6-11)
Remove Ink Tank
Problem 1:
Right cover was closed without removing the ink tank.
Solution:
Remove the ink tank.
Turn Power Off!!
Problem 1:
The tape inside the upper cover or the belt stopper have not been removed.
Solution:
Switch the printer off, open the upper cover, remove the tape and belt
stopper, then press the Power button. (
Æ
Setup Guide)
Problem 2:
The printer has malfunctioned.
Solution:
Switch the printer off, then press and hold down the Power button for over
3 seconds to switch the printer on again.
Solution:
If the message occurs again after switching the printer off and on, note the
message in the first line of the operation panel display, then call for
service.
W-Ink Full Soon
Problem 1:
The waste ink tank is nearly full and requires replacing very soon.
Solution:
Printing can continue after this message is displayed. However, you should
call for service as soon as possible before a Service Call is issued.