Canon imageCLASS MF7280 imageCLASS MF7280 Copying Guide - Page 32

Original Output Area, Size Originals mode. See Different Size Originals, on p. 3-23.

Get Canon imageCLASS MF7280 PDF manuals and user guides View all Canon imageCLASS MF7280 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

If any dirt on the original scanning area is detected when the originals are placed in the feeder, the following screen appears. Even though streaks may appear on the copies, you can continue to scan your documents by pressing [Done]. It is recommended, however, that you open the feeder, clean the scanning area, and then close the feeder. The following screen will not appear once the scanning area is clean. 1 For instructions on cleaning the original scanning area, see Chapter 7, "Routine Maintenance," in the Reference Guide. Introduction to Copying IMPORTANT • Do not add or remove originals while they are being scanned. • When scanning is complete, remove the originals from the original output area to avoid paper jams. Original Output Area NOTE • When you are enlarging an LTR or STMT original onto 11" x 17" or LGL paper, place the original horizontally. • The scanned originals are output to the original output area in the order that they are fed into the feeder. • You can place different size originals together into the feeder if you set the Different Size Originals mode. (See "Different Size Originals," on p. 3-23.) • 11" x 17" and LGL originals must be placed horizontally. 1-22 Placing Originals

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Placing Originals
1-22
1
Introduction to Copying
If any dirt on the original scanning area is detected when the originals are placed
in the feeder, the following screen appears. Even though streaks may appear on
the copies, you can continue to scan your documents by pressing [Done].
It is recommended, however, that you open the feeder, clean the scanning area,
and then close the feeder. The following screen will not appear once the
scanning area is clean.
For instructions on cleaning the original scanning area, see Chapter 7, "Routine
Maintenance," in the
Reference Guide
.
IMPORTANT
•
Do not add or remove originals while they are being scanned.
•
When scanning is complete, remove the originals from the original output area to
avoid paper jams.
NOTE
•
When you are enlarging an LTR or STMT original onto 11" x 17" or LGL paper,
place the original horizontally.
•
The scanned originals are output to the original output area in the order that they
are fed into the feeder.
•
You can place different size originals together into the feeder if you set the Different
Size Originals mode. (See "Different Size Originals," on p. 3-23.)
•
11" x 17" and LGL originals must be placed horizontally.
Original Output Area