Canon imageFORMULA CR-50 User Guide - Page 22

Logo top] / [Logo bottom], Configuration], Paper Cut settings]

Get Canon imageFORMULA CR-50 PDF manuals and user guides View all Canon imageFORMULA CR-50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

[End of page] Specify the paper feed volume at the end of a print page in the range of 0 to 255. Unit: dot per line (1 mm = 8 dots per line) [End of document] Specify the paper feed volume at the end of a document in the range of 0 to 255. Unit: dot per line (1 mm = 8 dots per line) [Paper Cut settings] [Paper Cut] Select whether to cut paper for each printed page or after printing a document (all pages). When you select [None], paper is not cut. [Cutting Method] When you select [Partial Cut], paper is cut except for its center. When you select [Full Cut], paper is cut completely. [Feed lines before Cut] Specify the paper feed volume before cutting paper in the range of 0 to 255. Unit: dot per line (1 mm = 8 dots per line) [Feed lines after Cut] Specify the paper feed volume after cutting paper in the range of 0 to 255. Unit: dot per line (1 mm = 8 dots per line) B [Logo (top)] / [Logo (bottom)] You can register a new logo or delete the registered logo. Logos smaller than 576 dots (width) and 10,000 lines (height) in monochrome BMP format can be registered. When a logo is registered as [Logo (top)], the logo is printed first, and when a logo is registered as [Logo (bottom)], the logo is printed last. IMPORTANT Depending on the software used, it may be possible to print logos without using this function. For information about logo printing by software, check with your software vendor. C [Configuration] [Export] Click to export the printer settings, logo settings in zip format. [Import] Click to apply the exported settings. [Test Print] Click this option if you want to print a test page. B Once configuration is complete, click [Close]. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
22
[End of page]
Specify the paper feed volume at the end of a print page in the
range of 0 to 255.
Unit: dot per line (1 mm = 8 dots per line)
[End of document]
Specify the paper feed volume at the end of a document in the
range of 0 to 255.
Unit: dot per line (1 mm = 8 dots per line)
[Paper Cut settings]
[Paper Cut]
Select whether to cut paper for each printed page or after printing
a document (all pages).
When you select [None], paper is not cut.
[Cutting Method]
When you select [Partial Cut], paper is cut except for its center.
When you select [Full Cut], paper is cut completely.
[Feed lines before Cut]
Specify the paper feed volume before cutting paper in the range of
0 to 255.
Unit: dot per line (1 mm = 8 dots per line)
[Feed lines after Cut]
Specify the paper feed volume after cutting paper in the range of
0 to 255.
Unit: dot per line (1 mm = 8 dots per line)
B
[Logo (top)] / [Logo (bottom)]
You can register a new logo or delete the registered logo. Logos
smaller than 576 dots (width) and 10,000 lines (height) in
monochrome BMP format can be registered. When a logo is
registered as [Logo (top)], the logo is printed first, and when a logo
is registered as [Logo (bottom)], the logo is printed last.
IMPORTANT
Depending on the software used, it may be possible to print logos without
using this function. For information about logo printing by software, check
with your software vendor.
C
[Configuration]
[Export]
Click to export the printer settings, logo settings in zip format.
[Import]
Click to apply the exported settings.
[Test Print]
Click this option if you want to print a test page.
B
Once configuration is complete, click [Close].