Canon imagePROGRAF iPF685 Setup Guide - Page 10
DNS Dync update
View all Canon imagePROGRAF iPF685 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
▲ ▲ ▲ ▲ When the printer cannot be found on the network If your printer cannot be found when connecting to the network for the first time, setup an IP address for the printer and then configure it on the printer. 1 On the tab selection screen of the control panel, press the and keys to select (settings/adj. tab) and press OK. When ink fills the system for the first time, after printhead adjustment is finished, specify the IP address on the printer's control panel. • When ink fills the system for the first time, do not operate the printer until printhead adjustment is finished. No Paper Loaded OK:Setting/Adj. Menu Maint.C Remain.: 80% Tot.Print Area(m2): 678 2 Use the ▲ and ▼ keys to select Interface Setup and press OK. 3 Use the ▲ and ▼ keys to select TCP/IP and press OK. 4 Enter the IP address. Navigate through the following menus using the ▲ and ▼ keys on the control panel. 1.Select IPv4 and press OK. 2.Select IPv4 Settings and press OK. 3.Select IP Address and press OK. 4.Enter the IP address. How to enter IP addresses MEMO 1. Press the and keys to select a field for inputting values. 2. Use the ▲ and ▼ keys to input values. • Pressing ▲ increases the value by one. • Pressing ▼ decreases the value by one. • Holding down either the ▲ or ▼ keys continually increases or decreases the value. 3. Press OK once you have finished. 5 Press Menu. 6 Press OK on the registration confirmation message that appears. The IP address is set on the printer. Next, restart installation of the printer driver. 7 In the Search Results window, select Specify the IP address of available printers in the network and click Next. When the IP Address Specifications window appears, follow the instructions of "When entering the printer's IP address manually" in step 8 to 11 on page 9 to complete the installation of the software. • If the following screen appears, click MEMO Retry and select Specify the IP address of available printers in the network on the next screen that appears. Using DHCP To use the DHCP server function to automatically allocate an IP address to the printer, one of the following settings needs to be configured. Check with your network administrator for the settings that match your system. When used in an environment with a DNS server Configure the DNS dynamic update function in the printer and register the printer DNS host name with the DNS server. When used in an environment without a DNS server Configure the DHCP server to always allocate the same IP address to the printer. This section describes how to turn on DNS dynamic update from the control panel of the printer. • The DNS dynamic update function can MEMO also be configured using Remote UI. Refer to "Configuring the Printer's TCP/ IP Network Settings With RemoteUI" in the user guide for details. 1 Perform steps 1 to 3 of the procedure in "When the printer cannot be found on the network" on page 10. 2 Select IPv4 or IPv6 using the ▲ and ▼ keys and then press OK. 3 Select DNS Settings using the ▲ and ▼ keys and then press OK. 4 Select DNS Dync update using the ▲ and ▼ keys and then press OK. 5 For IPv4 Select On using the ▲ and ▼ keys and then press OK. For IPv6 1. When Use the same host name and domain name as IPv4? is displayed, select Off using the ▲ and ▼ keys and then press OK. 2. Select Statefull Addr using the ▲ and ▼ keys and then press OK, and then select On using the ▲ and ▼ keys and then press OK. 3. Set Stateless Addr to On using the same procedure as in Step 2. 10