Canton DM 90.2 Owners Manual - Page 45

m => System Setup => Output Config => Volume - manual

Get Canton DM 90.2 PDF manuals and user guides View all Canton DM 90.2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Espagnol Français English Deutsch DM System - Functions No inputs except "radio" can be selected 1. No inputs have been registered in the "input config" menu (e.g. initial installation was terminated with "exit") 2. During the configuration process the "up" or "down" arrow keys and / or the "exit" key were used DM System does not recognise Dolby Digital or DTS data stream 1. The source is only connected to the analog port (Line 1 or 2) 2. The wrong settings have been selected on the source device No signal from Zone2 / Line - Output 1. There should be a multi-channel signal from Zone2 / Line RC only displays "surround" instead of "surround 1" and "surround 2" 2. The volume for Zone2 is set too low 1. The DM System has been set to 4.1 or 5.1 mode 1. Register the relevant inputs in the "input config" menu (m => System Setup => input config). Follow the exact instructions on page 36! 2. Register the relevant inputs in the "Eingangskonfig" menu (m => System Menu => Eingangskonfig) and only use the correct keys (see page 36) 1. Connect a digital output from the source device to Opt 1 / 2 or Coax 1 /2 2. Select "Bitstream" or "Raw" as the data format on the source device (referring to the instructions given for the source device) 1. Set "dynamic" (m => System Setup => Dynamic) to „comp", under "Output Config" (m => System Setup => Output Config => Input) select "zone 1" as the input and on the main screen select the desired source as input 2. Increase the volume for Zone2 - output under "Volume" (m => System Setup => Output Config => Volume) 1. Set the system to 2.1 mode under "system preset" (m => System Setup => factory setup => System Preset) Distorted radio reception A set radio station is no longer available once the system has been switched off and on again (display back on 87.50) Sound and image are not (lip)synched 1. Poor aerial position 2. Poor geographical location 3. The station has not been properly set 1. The station was not allocated a programme slot 1. Long processing times in the TV delay the image 1. Arrange the extended (!) aerial as openly as possibly, well away from metal surfaces 2. Use a roof-mounted aerial or a broadband cable connection 3. Tune the station manually, following the instructions on page 39 1. Simply press the "OK" key to save a station in Programme Slot 1 1. Delay the sound in "lip sync" (m => System Menu => lip sync) so that the image and sound are synchronised (simulta neous) 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
45
English
DM System – Functions
No inputs except “radio” can be selected
1. No inputs have been registered in the “input config” menu
1. Register the relevant inputs in the “input config” menu
(e.g. initial installation was terminated with “exit”)
(m => System Setup => input config). Follow the exact
instructions on page 36!
2. During the configuration process the “up” or “down” arrow
2. Register the relevant inputs in the “Eingangskonfig” menu
keys and / or the “exit” key were used
(m => System Menu => Eingangskonfig) and only use the
correct keys (see page 36)
DM System does not recognise Dolby Digital or DTS data stream
1. The source is only connected to the analog port (Line 1 or 2)
1. Connect a digital output from the source device to Opt 1 / 2
or Coax 1 /2
2. The wrong settings have been selected on the source device
2. Select “Bitstream” or “Raw” as the data format on the
source device (referring to the instructions given for the
source device)
No signal from Zone2 / Line - Output
1. There should be a multi-channel signal from Zone2 / Line
1. Set “dynamic” (m => System Setup => Dynamic) to „comp“,
under “Output Config” (m => System Setup => Output
Config => Input) select “zone 1” as the input and on the
main screen select the desired source as input
2. The volume for Zone2 is set too low
2. Increase the volume for Zone2 – output under “Volume”
(m => System Setup => Output Config => Volume)
RC only displays “surround” instead of “surround 1” and
1. The DM System has been set to 4.1 or 5.1 mode
1. Set the system to 2.1 mode under “system preset” (m =>
“surround 2”
System Setup => factory setup => System Preset)
Distorted radio reception
1. Poor aerial position
1. Arrange the extended (!) aerial as openly as possibly, well
away from metal surfaces
2. Poor geographical location
2. Use a roof-mounted aerial or a broadband cable connection
3. The station has not been properly set
3. Tune the station manually, following the instructions on
page 39
A set radio station is no longer available once the system has
1. The station was not allocated a programme slot
1. Simply press the “OK” key to save a station in Programme
been switched off and on again (display back on 87.50)
Slot 1
Sound and image are not (lip)synched
1. Long processing times in the TV delay the image
1. Delay the sound in “lip sync” (m => System Menu => lip
sync) so that the image and sound are synchronised (simulta
neous)