Canton DM 90.2 Owners Manual - Page 46

DM System -> Volume, DM System - Sound

Get Canton DM 90.2 PDF manuals and user guides View all Canton DM 90.2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

DM System -> Volume No (music) playback Volume will not go above a certain value (System Setup => factory set => line2 config) 1. Set the volume limiter (m => System Setup => factory set => max volume) to the desired value (max. 99) 1. Set the "start volume" (m => System Setup => factory set => start volume) to the desired value (max. 99 but not higher than "max volume") 1. In the Loudspeaker Menu use (m => Speaker Setup => Level Trim) to set the correct volume levels and (m => Speaker Setup => Speaker Distance) to set the correct distances DM System - Sound In Surround Mode there is little or no surround sound 1. The Play Mode is set on "stereo" or "wide" 2. The listening spot is not central enough 3. The source only supplies a 2-channel signal 4. The DM System is set to 4.1/5.1 mode 46 1. Set Play Modes to "surround 1" or "surround 2" 2. In the Loudspeaker Menu use (m => Speaker Setup => Level Trim) to set the correct volume levels and (m => Speaker Setup => Speaker Distance) to set the correct distances to the listening spot 3. To achieve optimal sound in the room the DM System requires a multi-channel data stream. In this case the RC displays "virtual Dolby Digital" or "virtual DTS". All other displays (e.g. "Virtual Dolby PLII) mean that it is not a multichannel data stream, which leads to less of a surround sound impression 4. Set the system to a 2.1 Mode with virtual surround-mode at "System Preset" (m => System Setup => factory setup => System Preset)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
46
DM System -> Volume
No (music) playback
1. The DM System is switched off or in Standby mode
1. Switch the DM System on so that the RC displays the main
screen
2. The volume is set low or on mute
2. Use Volume + (V+) to increase the volume
3. The wrong input has been selected
3. Select the input that is connected to the relevant source
4. The signal (data stream) from the source has not been
4. Set the source to a different data format or select another
recognised by the DM System
audio format during playback (referring to the instructions of
the source device)
5. Wrong setting of Line2 / Phono input when using a
5. Set Line 2 / Phono – Input “line2 config” to “phono” (m
record player
=>System Setup => factory set => line2 config)
Volume will not go above a certain value (</=99)
1. The “max volume” is set to the maximum possible value
1. Set the volume limiter (m => System Setup => factory set =>
max volume) to the desired value (max. 99)
DM System is quieter when switched on than when switched off
1. The “start volume” is set to a value that is lower than
1. Set the “start volume” (m => System Setup => factory
the volume set before switching off
set => start volume) to the desired value (max. 99 but
not higher than “max volume”)
The balance is wrong (location is not central)
1. The volume adjustment of the satellite speakers is wrongly set
1. In the Loudspeaker Menu use (m => Speaker Setup =>
or the listening spot is not central
Level Trim) to set the correct volume levels and (m =>
Speaker Setup => Speaker Distance) to set the correct
distances
DM System – Sound
In Surround Mode there is little or no surround sound
1. The Play Mode is set on “stereo” or “wide”
1. Set Play Modes to “surround 1” or “surround 2”
2. The listening spot is not central enough
2. In the Loudspeaker Menu use (m => Speaker Setup =>
Level Trim)
to set the correct volume levels and
(m => Speaker Setup => Speaker Distance) to set the correct
distances to the listening spot
3. The source only supplies a 2-channel signal
3. To achieve optimal sound in the room the DM System
requires a multi-channel data stream. In this case the RC
displays “virtual Dolby Digital” or “virtual DTS”. All other
displays (e.g. “Virtual Dolby PLII) mean that it is not a multi-
channel data stream, which leads to less of a surround sound
impression
4. The DM System is set to 4.1/5.1 mode
4. Set the system to a 2.1 Mode with virtual surround-mode at
“System Preset” (m => System Setup => factory setup =>
System Preset)