Carvin 1584 Instruction Manual - Page 3

NON-POWERED MODELS REAR CONNECT PLATE (non-powered speakers) - Use either 1/4" or Speakon™ cables for connecting to the power amp and daisy chaining to an additional speaker. For high powered applications, use Speakon™ cables only. SUGGESTIONS FOR OPTIMAL PERFORMANCE To help control feedback, use a graphic equalizer. Keep the speakers in front of the microphone. Never direct the microphone towards the speaker. For greater coverage, add additional speakers. Doubling the speakers adds four times the acoustical power which is more advantagious than increasing power. INPUT 742 PRO SOUND REINFORCEMENT IMPEDANCE: 8 Ohms POWER RATING: 400 Watts JACKS WIRED PARALLEL TWIST-LOK 1+ SIGNAL 1- GROUND 2+ NOT USED 2- NOT USED EXT. SYSTEM SPEAKER CABLES Use either Carvin's PH50 speaker cable for up to 50' or highcurrent 12GA Speakon™ cables for lengths up to 150'. 18GA cables are not recomended. You can DAISY-CHAIN up to one additional speaker per cable by using the OUTPUT connector. Be sure the total impedance to the amp is not lower than the amp's minimum impedance. TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS Individual speaker or speaker cabinet wiring examples for total impedance. Serial No. MADE IN THE USA Speakon™ & 1/4" inputs from power amp output. Speakon™ & 1/4" through connectors for additional speakers TYPICAL STEREO SETUP For (stereo) the PARALLEL switch must be OFF (OUT). Ch 1 Left BRIDGE switch must be OFF (OUT). SPEAKER - 1 + --BRIDGE-- + - SPEAKER 2 CA UTION RISK OF ELECTRIC SHOCK DO NO T OPEN CAUTION - TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY GROUND ON THE POWER CORD - DO NOT REMOVE COVER . WARNING - TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFED PERSONNEL. PROFESSIONAL STEREO POWER AMPLIFIER SERIAL NUMBER GND LIFT PARALLEL BRIDGE CH1 IN LIMITERS XLR PIN 1 GND PIN 2 POS PIN 3 NEG 120V~60Hz Slow Blow FUSE 8AG 700VA Ch 2 Right STEREO CROSSOVER Suggested settings Left Input XC3000 1-800-854-2235 Electronic Crossover www.carvin.com INTERNAL FUSE 90-250 VAC 10 VA ~50-60HZ GND LIFT CHANNEL ONE HIGH PHASE MID PHASE MONO [ LOW 1+2 ] LOW PHASE STEREO BIAMPING Right Input SWITCHABLE TO MONO [ LOW 1+2] CHANNEL TWO HIGH PHASE MID PHASE LOW PHASE Right High Out Left Low Out Right Low Out SPEAKER - 1 + --BRIDGE-- + - SPEAKER 2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION - TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY GROUND ON THE POWER CORD - DO NOT REMOVE COVER . WARNING - TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFED PERSONNEL. Left High Out PROFESSIONAL STEREO POWER AMPLIFIER SERIAL NUMBER GND LIFT PARALLEL BRIDGE CH1 IN LIMITERS XLR PIN 1 GND PIN 2 POS PIN 3 NEG Low Frequency Amp 120V~60Hz Slow Blow FUSE 8AG 700VA Left Highs SPEAKER - 1 + --BRIDGE-- + - SPEAKER 2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION - TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY GROUND ON THE POWER CORD - DO NOT REMOVE COVER . WARNING - TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFED PERSONNEL. PROFESSIONAL STEREO POWER AMPLIFIER SERIAL NUMBER GND LIFT PARALLEL BRIDGE CH1 IN LIMITERS XLR PIN 1 GND PIN 2 POS PIN 3 NEG High Frequency 120V~60Hz Slow Blow FUSE 8AG 700VA Left Full Range Right Full Range Standard 1/4" Phone Plug Tip-Sleeve Sleeve Tip Tip (Positive) Sleeve (Negative) Right Highs Left Lows Right Lows 2+ 2- 11+ Solder tinned wires 1/4" Strip cable insulation back 3/4" Speakon™ • Slip "Securing Hub" then "Cable Clamp" over cable before attaching wires. • Connection Configuration: Black (1+) / positive White (1-) / negative Red (2+) / positive Green (2-) / negative • Solder wires in contacts or use hex screws provided. Twist-Lok Housing Contact Insert Cable Clamp Securing Hub