Carvin CX630 Instruction Manual - Page 3

R16 Resistor, 10K, 1/4W, ±5% 50-10045 R17 Resistor, 10K, 1/4W, ±5% 50-10045 R18 Resistor, 4.70K, 1/4W, ±5% 50-47035 R19 Resistor, 4.70K, 1/4W, ±5% 50-47035 R20 Resistor, 22Ω, 1/2W, ±5% 52-22015 R21 Resistor, 22Ω, 1/2W, ±5% 52-22015 R30 Resistor, 47K, 1/4W, ±5% 50-47045 R31 Resistor, 2.2K, 1/4W, ±5% 50-22035 R32 Resistor, 33K, 1/4W, ±5% 50-33045 R33 Resistor, 27K, 1/4W, ±5% 50-27045 R34 Resistor, 33K, 1/4W, ±5% 50-33045 R35 Resistor, 10K, 1/4W, ±5% 50-10045 R36 Resistor, 10K, 1/4W, ±5% 50-10045 R37 Resistor, 10K, 1/4W, ±5% 50-10045 R38 Resistor, 10K, 1/4W, ±5% 50-10045 R39 Jumper, 0Ω, Carbon, 0 50-00035 R40 Jumper, 0Ω, Carbon, 0 50-00035 R41 Resistor, 150K, 1/4W, ±5% 50-15055 R42 Resistor, 470Ω, 1/4W, ±5% 50-47025 R43 Resistor, 470Ω, 1/4W, ±5% 50-47025 R44 Resistor, 150K, 1/4W, ±5% 50-15055 R45 Resistor, 470Ω, 1/4W, ±5% 50-47025 R46 Resistor, 33K, 1/4W, ±5% 50-33045 R47 N/U R48 Jumper, 0Ω, Carbon, 0 50-00035 R49 Resistor, 150K, 1/4W, ±5% 50-15055 R50 Resistor, 470Ω, 1/4W, ±5% 50-47025 R51 Resistor, 4.70K, 1/4W, ±5% 50-47035 R52 Resistor, 47K, 1/4W, ±5% 50-47045 R53 Resistor, 100Ω, 1/4W, ±5% 50-10025 R54 Resistor, 150K, 1/4W, ±5% 50-15055 R55 Resistor, 10K, 1/4W, ±5% 50-10045 R60 Resistor, 2.4K, 1/4W, ±5% 50-24035 R61 Resistor, 150K, 1/4W, ±5% 50-15055 R62 Resistor, 2.2K, 1/4W, ±5% 50-22035 R63 Resistor, 220K, 1/4W, ±5% 50-22055 R64 Resistor, 2.2K, 1/4W, ±5% 50-22035 R65 Resistor, 300K, 1/4W, ±5% 50-30055 R66 Resistor, 2.4K, 1/4W, ±5% 50-24035 4 3 2 1 R67 R68 R69 R70 R71 R72 R73 R74 R75 R76 R77 R78 R79 R80 R81 R82 R83 R90 R91 R92 R93 R94 R95 R96 R97 R98 R99 R100 R101 R102 R103 Resistor, 180K, 1/4W, ±5% Resistor, 2.2K, 1/4W, ±5% Resistor, 360K, 1/4W, ±5% Resistor, 2.0K, 1/4W, ±5% Resistor, 130K, 1/4W, ±5% Resistor, 2.2K, 1/4W, ±5% Resistor, 110K, 1/4W, ±5% Resistor, 2.2K, 1/4W, ±5% Resistor, 110K, 1/4W, ±5% Resistor, 1.8K, 1/4W, ±5% Resistor, 91K, 1/4W, ±5% Resistor, 10K, 1/4W, ±5% Resistor, 150K, 1/4W, ±5% Resistor, 470Ω, 1/4W, ±5% Resistor, 4.70K, 1/4W, ±5% Resistor, 1K, 1/4W, ±5% Resistor, 4.70K, 1/4W, ±5% Resistor, 350Ω, 10W, ±10% Resistor, 350Ω, 10W, ±10% Jumper, 0Ω, Carbon, 0 Jumper, 0Ω, Carbon, 0 Jumper, 0Ω, Carbon, 0 Resistor, 680Ω, 1/4W, ±5% Resistor, 15K, 1/4W, ±5% Resistor, 22K, 1/4W, ±5% Resistor, 22K, 1/4W, ±5% Resistor, 10K, 1/4W, ±5% Resistor, 33K, 1/4W, ±5% Resistor, 680Ω, 1/4W, ±5% Resistor, 15K, 1/4W, ±5% Resistor, 22K, 1/4W, ±5% 50-18055 50-22035 50-36055 50-20035 50-13055 50-22035 50-11055 50-22035 50-11055 50-18035 50-91045 50-10045 50-15055 50-47025 50-47035 50-10035 50-47035 56-35010 56-35010 50-00035 50-00035 50-00035 50-68025 50-15045 50-22045 50-22045 50-10045 50-33045 50-68025 50-15045 50-22045 S1 Switch DPDT Push PC Mtg 25-02201 S4 Switch DPDT Push PC Mtg 25-02201 U1 100V/100W DMOS Audio Amp 60-72940 U2 100V/100W DMOS Audio Amp 60-72940 All "B" Reference Designators are 0 ohm jumpers. 5 6 7 # DESCRIPTION 1. Switch Cap Grey Extended 2. Knob 11 D shaft (COLOR) 3. Front Panel PCB (6 Chan) 4. POWER TRANSFORMER 5. Accutronics™ REVERB TANK 6. SPEAKER JACK PCB 7. POWER AMP PCB CARVIN # 07-01603 07-120-80-0630-1 15-15070B 70-00821 80-0630-3 80-0630-2 QTY 7 --1 1 2 1 1 Color Knob Code Yellow 20 Green 25 Drk Grey 28 17 QUICK START UP If you're like most new owners, you're probably in a hurry to plug your CX mixer in and use it. Here are some brief instructions to get you going quickly. With the mixer unplugged and turned off complete the following procedures: 1. CONNECTING AC POWER TO YOUR MIXER • Check the rear panel to make sure the mixer received uses the proper AC Line Voltage. (USA 120VAC, Europe 240 VAC ...etc.) • Use only a grounded (3 prong) power outlet to prevent a shock hazard. This gives the quietest grounding for your mixer. 2. CONNECTING SPEAKERS • For connecting speakers, use the two 1/4" speaker jacks on the rear panel. These jacks are controlled by the main level control on the front panel. The speaker cables should be non-shielded and at least 18 gauge(AWG) wire. For speaker cable runs of over 20 feet 16 gauge wire is recommended. NOTE: Do not run your speakers through microphone cables, guitar cables, or multi-conductor microphone junction boxes or "snakes" as they are sometimes referred to. This wire is normally shielded and of a very light gauge causing a substantial loss of power and oscillations at high frequencies in the amplifier. All speaker wires must be non-shielded. 3. CONNECTING INPUTS TO YOUR MIXER • For low level balanced devices such as microphones, plug into the balanced MIC inputs using an XLR shielded microphone cable. • For high level unbalanced devices such as Tape Recorders and Keyboards plug into the LINE input jacks using a 1/4" phone shielded cable. 4. TURNING YOUR MIXER ON • Adjust all channel and master level controls to the off position (fully counter clockwise). • Adjust all "EQ" tone controls, the channel's Hi, Mid, and Lo and the master 9 Band Graphic EQ, to their center detent position. • Turn the mixer on by the rear panel power switch and watch for the power LED to come on. Your mixer is now ready to operate. MAINTENANCE To bring back the new look, your CX mixer can be washed with mild detergent and/ or a warm damp soft cloth. This will remove normal dust and oil from the front and back panels. Never spray cleaners or detergents directly at the unit. The mixer's are virtually sealed from outside dust and dirt, but it is recommended to keep the mixer free from dust, dirt, and moisture as much as possible. 2