Carvin CX630 Instruction Manual - Page 9
Channel Features, Cx Mono Series Parts List
View all Carvin CX630 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
CHANNEL FEATURES 1. LINE INPUT JACK The 1/4" LINE phone jack is designed for unbalanced line and instrument level inputs. Examples of these inputs would be instruments such as a guitar, a keyboard, unbalanced mics, or a pre amp output. The line input can be used at the same time the mic input is being used. 2. XLR MICROPHONE INPUT The XLR MIC input is designed for balanced low 5 impedance ( microphone ) input signals. The balance means the input differential amplifier will reduce the common noise picked up on the microphone cables. The XLR connector is wired as per the industry stan- 4 dard, pin 1 is ground, pin 2 is non-inverting (positive), and pin 3 is inverting (negative). Phantom power is available on every XLR input jack when the phantom power switch, in the master section, 3 MON 4 5 6 3 7 2 8 1 9 0 10 45 6 3 7 2 8 1 9 0 10 LEVEL 20 dB 1 is pressed. This feature allows condenser micro- phones to be run directly from the mixer. Note: When using phantom power make sure the phantom power is switched off before connecting or disconnecting microphones to the mixer. It is recom- 2 mended to allow 5 seconds for the phantom power to discharge before making any microphone connections. Also to avoid hearing a pop, turn down the main vol- MIC ume when turning on the phantom power. 1 3. -20DB PAD SWITCH This switch reduces the input gain on both the line and LINE mic input jacks by 20dB. If distortion is heard regardless of the channel LEVEL control's setting, engage this switch. This will eliminate the over-driving of the input amplifier before the channel level control. 4. CHANNEL LEVEL CONTROL The LEVEL control adjusts the final volume of the channel. Here is where the individual channel volumes are adjusted to make up the desired mix heard at the main output. A general rule to prevent distortion with in the mixer, is to always keep the MAIN master level the same or higher than the channel LEVEL. 5. MONITOR LEVEL CONTROL The MONITOR level control adjusts the volume of the channel going to the monitor mix. Here is where the individual channel monitor volumes are adjusted to make up the desired mix heard at the monitor output. The monitor level control is pre channel's level and tone controls. This means it is unaffected by adjustments in channel's level or tone controls. The purpose for this is so the main mix adjustments for tone and level can be made without disturbing the monitor mix. 3 RefDes A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C56 C57 C58 C59 C60 C61 C62 C63 C70 C71 C72 C73 C76 C77 CX MONO SERIES PARTS LIST CAUTION RISK OF ELECTRIC SHOCK THIS UNIT CONTAINS HIGH VOLTAGE COMPONENTS INSIDE! REFER SERVICING TO QUALIFIED SERVICE PERSONNEL! DESCRIPTION CARVIN # 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 4558, Dual Low Noise Op Amp 60-45580 Capacitor, Cera 82pF, 500V 45-82052 Capacitor, Cera 82pF, 500V 45-82052 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Cera 27pF, 500V 45-27052 Capacitor, Cera 27pF, 500V 45-27052 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Cera 330pF, 1000V 45-33113 Cap, Poly 0.0047µF, 100V 46-47212 Capacitor, Cera 39pF, 500V 45-39052 Capacitor, Elec 47µF, 63V 47-47061 Capacitor, Poly 0.047µF, 100V 46-47312 Capacitor, Poly 0.047µF, 100V 46-47312 Capacitor, Poly 0.1µF, 100V 46-10412 Capacitor, Cera 39pF, 500V 45-39052 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Cera 39pF, 500V 45-39052 Capacitor, Elec 470µF, 16V 47-47116 Capacitor, Cera 39pF, 500V 45-39052 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Elec 470µF, 16V 47-47116 Capacitor, Cera 39pF, 500V 45-39052 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Cera 39pF, 500V 45-39052 Capacitor, Elec 10µF, 50V 47-10051 N/U Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Poly 0.047µF, 100V 46-47312 Capacitor, Cera 120pF, 500V 45-12152 Capacitor, Elec .47µF, 100V 46-47412 Capacitor, Poly 0.022µF, 100V 46-22312 Capacitor, Poly 0.22µF, 100V 46-22412 Capacitor, Poly 0.01µF, 100V 46-10312 Capacitor, Poly 0.1µF, 100V 46-10412 Capacitor, Poly 0.0047µF, 100V 46-47212 Capacitor, Poly 0.068µF, 100V 46-68312 Capacitor, Poly 0.0033µF, 100V 46-33212 Capacitor, Poly 0.033µF, 100V 46-33312 Capacitor, Poly 0.001µF, 100V 46-10212 Capacitor, Poly 0.022µF, 100V 46-22312 Capacitor, Poly 0.001µF, 100V 46-10212 Capacitor, Poly 0.0068µF, 100V 46-68212 Capacitor, Poly 0.001µF, 100V 46-10212 Capacitor, Poly 0.0047µF, 100V 46-47212 Capacitor, Cera 330pF, 1000V 45-33113 Capacitor, Poly 0.0022µF, 100V 46-22212 Capacitor, Cera 250pF, 500V 45-25152 Capacitor, Cera 56pF, 500V 45-56052 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Poly 0.047µF, 100V 46-47312 Capacitor, Elec 470µF, 16V 47-47116 Capacitor, Elec 470µF, 25V 47-47125 Capacitor, Elec 470µF, 25V 47-47125 Capacitor, Elec 470µF, 25V 47-47125 Capacitor, Elec 470µF, 25V 47-47125 Capacitor, Elec 4700µF, 50V 42-47251 Capacitor, Elec 4700µF, 50V 42-47251 Capacitor, Elec 10µF, 50V 47-10051 Capacitor, Elec 10µF, 50V 47-10051 C78 Capacitor, Poly 0.1µF, 100V 46-10412 C79 Capacitor, Elec 22µF, 160V 47-22016 C80 Capacitor, Poly 0.1µF, 100V 46-10412 C81 Capacitor, Elec 10µF, 50V 47-10051 C82 Capacitor, Elec 10µF, 50V 47-10051 C83 Capacitor, Elec 10µF, 50V 47-10051 C84 Capacitor, Elec 10µF, 50V 47-10051 C85 Capacitor, Poly 0.1µF, 100V 46-10412 C86 Capacitor, Elec 22µF, 160V 47-22016 C87 Capacitor, Poly 0.1µF, 100V 46-10412 C88 Capr, Mylar 0.047µF, 250VAC 41-47321 D1 LED, Small Red 60-75320 D2 LED, Small Red 60-75320 D3 Diode, 1N4003 0.35" prep. 61-40030 D7 Diode, 1N914 0.35" prep. 61-19140 D10 Diode Rect., MR752 6A 200V 60-75200 D11 Diode Rect., MR752 6A 200V 60-75200 D12 Diode Rect., MR752 6A 200V 60-75200 D13 Diode Rect., MR752 6A 200V 60-75200 F1 Fuse Clips 3AG Vert. PC MTG 23-03529 H1 Conn. Hdr. 8 pin 90° 23-10008 H2 Conn. Hdr 4 pin 90° 23-10014 H3 Conn. Hdr 8 pin 23-10082 J1 XLR Female Neutrik Conn. 21-40000 J2 Jack 1/4", 3Pin Plastic. 24mm 21-06453 J3 Jack RCA Quad PC Vert. MTG 21-40022 J4 Jack 1/4", 3Pin Plastic. 24mm 21-06453 J5 Not Assigned J6 Jack 1/4", 3Pin Plastic. 24mm 21-06453 J7 Jack 1/4", 3Pin Plastic. 24mm 21-06453 J8 Jack 1/4", 3Pin Plastic. 24mm 21-06453 J9 Jack 1/4", 3Pin Plastic. 24mm 21-06453 J10 Jack 1/4", 3Pin Plastic. 24mm 21-06453 J11 Jack 1/4", 3Pin Plastic. 24mm 21-06453 P1 Pot, 12x35mm "D", B50K-C 71-13057 P2 Pot, 12x35mm "D", B50K-C 71-13057 P3 Pot, 12x35mm "D", B50K-C 71-13057 P4 Pot, 12x35mm "D", B50K 71-13056 P5 Pot, 12x35mm "D", B50K 71-13056 P6 Pot, 12x35mm "D", B50K 71-13056 P7 Pot, 12x35mm "D", B50K 71-13056 P8 Pot, 12x35mm "D", B50K 71-13056 P9 Pot, 12x35mm "D", B50K 71-13056 P10 Pot, 12x35mm "D", B50K 71-13056 P11 Pot, 12x35mm "D", B50K 71-13056 P20 FADER 50K OHM 71-10332 P21 FADER 50K OHM 71-10332 P22 FADER 50K OHM 71-10332 P23 FADER 50K OHM 71-10332 P24 FADER 50K OHM 71-10332 P25 FADER 50K OHM 71-10332 P26 FADER 50K OHM 71-10332 P27 FADER 50K OHM 71-10332 P28 FADER 50K OHM 71-10332 R1 Resistor, 5.62K, 1/4W, ±1% 50-56231 R2 Resistor, 5.62K, 1/4W, ±1% 50-56231 R3 Resistor, 2.21K, 1/4W, ±1% 50-22131 R4 Resistor, 2.21K, 1/4W, ±1% 50-22131 R5 Resistor, 47K, 1/4W, ±5% 50-47045 R6 Resistor, 10K, 1/4W, ±5% 50-10045 R7 Resistor, 100K, 1/4W, ±5% 50-10055 R8 Resistor, 300K, 1/4W, ±5% 50-30055 R9 Resistor, 100K, 1/4W, ±5% 50-10055 R10 Resistor, 10K, 1/4W, ±5% 50-10045 R11 Resistor, 300K, 1/4W, ±5% 50-30055 R12 Resistor, 2.2K, 1/4W, ±5% 50-22035 R13 Resistor, 100K, 1/4W, ±5% 50-10055 R14 Resistor, 150K, 1/4W, ±5% 50-15055 R15 Resistor, 2.2K, 1/4W, ±5% 50-22035 16