Chamberlain B4655T Installation Manual - English - Page 34

Test the Safety Reversal System, 4 - Test the Protector System®, Battery Backup, MODELS B4613T

Get Chamberlain B4655T PDF manuals and user guides View all Chamberlain B4655T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Adjustments 3 - Test the Safety Reversal System Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal system MUST be tested every month. • After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" (3.8 cm) high object (or 2x4 laid flat) on the floor. 1 With the door fully open, place a 1-1/2 inch (3.8 cm) board (or a 2x4 laid flat) on the floor, centered under the garage door. 2 Press the remote control push button to close the door. The door MUST reverse when it makes contact with the board. If the door stops but does not reverse: 1. Repeat Program the Travel (see Adjustment Step 1); 2. Repeat the Safety Reversal test. If the test continues to fail, call a trained door systems technician. 4 - Test the Protector System® Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. 1 Open the door. Place an obstruction in the path of the door. 2 Press the remote control push button to close the door. The door will not move more than an inch (2.5 cm). The garage door opener will not close from a remote control if the LED in either safety reversing sensor is off (alerting you to the fact that the sensor is misaligned or obstructed). If the garage door opener closes the door when the safety reversing sensor is obstructed (and the sensors are no more than 6 inches [15 cm] above the floor), call for a trained door systems technician. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
34
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED or
KILLED by a closing garage door.
•
Safety reversal system MUST be tested every month.
•
After ANY adjustments are made, the safety reversal system
MUST be tested. Door MUST reverse on contact with 1-1/2”
(3.8 cm) high object (or 2x4 laid flat) on the floor.
If the door stops but does not reverse:
1.
Repeat Program the Travel (see Adjustment Step 1);
2.
Repeat the Safety Reversal test.
If the test continues to fail, call a trained door systems technician.
Without a properly installed safety reversing sensor, persons
(particularly small children) could be SERIOUSLY INJURED or
KILLED by a closing garage door.
1
Open the door. Place an obstruction in the path of the door.
2
Press the remote control push button to close the door. The door will
not move more than an inch (2.5 cm).
Adjustments
3
- Test the Safety Reversal System
1
With the door fully open, place a 1-1/2 inch (3.8 cm) board (or a 2x4
laid flat) on the floor, centered under the garage door.
2
Press the remote control push button to close the door. The door
MUST reverse when it makes contact with the board.
4
- Test the Protector System
®
The garage door opener will not close from a remote control if the LED in
either safety reversing sensor is off (alerting you to the fact that the sensor
is misaligned or obstructed).
If the garage door opener closes the door when the safety reversing sensor
is obstructed (and the sensors are no more than 6 inches [15 cm] above
the floor), call for a trained door systems technician.