Home » Chamberlain Manuals » Garage Door Openers » Chamberlain WD962KEV » Manual Viewer

Chamberlain WD962KEV WD962KEV Manual - Page 4

Carton Inventory, The Protector System, NOT SHOWN - installation manual

View all Chamberlain WD962KEV manuals

Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Preparation Carton Inventory Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories vary depending on the garage door opener model purchased. Depending on your model, other accessories may be included with your garage door opener. Instructions for these accessories will be attached to the accessory and are not included in this manual. Save the carton and packing material until the installation and adjustment is complete. The images throughout this manual are for reference only and your product may look different. A. Header bracket B. Pulley C. Door bracket D. Curved door arm E. Straight door arm (Packaged inside front rail section) F. Trolley NOTE: Be sure to assemble the trolley before sliding onto rail. G. Emergency release rope and handle H. Rail (1 front and 4 center sections) I. Hanging brackets (2) (Packaged inside the front rail section) J. Garage door opener (motor unit) K. Sprocket cover and screws L. "U" bracket M. Belt N. Door control (Motion-Detecting Control Panel or Smart Control Panel®) O. Remote control P. The Protector System® Safety reversing sensors with 2 conductor white and white/black wire attached: Sending Sensor (1), Receiving Sensor (1), and Safety Sensor Brackets (2) NOT SHOWN White and red/white wire Owner's manual Hardware 3 A B C F D E G P OR M H I N K L J O

Section	Page
Owner's Manual	1
CONTENTS	1
Preparation	2
Safety Symbol and Signal Word Review	2
Check the Door	2
Additional Items You May Need:	3
Tools Needed	3
Carton Inventory	4
Hardware Inventory	5
Assembly	6
STEP 1 Assemble the rail and trolley	6
STEP 2 Fasten the rail to the motor unit	7
STEP 3 Install the idler pulley	8
STEP 4 Install the belt	9
STEP 5 Tighten the belt and install the sprocket cover	10
Installation	11
STEP 1 Determine the header bracket location	12
STEP 2 Install the header bracket	13
OPTION A WALL INSTALLATION	13
OPTION B CEILING INSTALLATION	13
STEP 3 Attach the rail to the header bracket	14
STEP 4 Position the garage door opener	14
STEP 5 Hang the garage door opener	15
STEP 6 Install the light bulbs	16
STEP 7 Attach the emergency release rope and handle	16
STEP 8 Install the door bracket	17
OPTION A SECTIONAL DOORS	17
OPTION B ONE-PIECE DOORS	18
STEP 9 Connect the door arm to the trolley	19
OPTION A SECTIONAL DOORS	19
OPTION B ONE-PIECE DOORS	20
STEP 10 Install the door control	21
STEP 11 Wire the door control to the garage door opener	22
STEP 12 Attach the warning labels	22
STEP 13 Install the Protector System®	23
OPTION A DOOR TRACK INSTALLATION	23
OPTION B WALL INSTALLATION	24
OPTION C FLOOR INSTALLATION	24
STEP 14 Wire the Safety Reversing Sensors	25
OPTION A INSTALLATION WITHOUT PRE-WIRING	25
OPTION B PRE-WIRED INSTALLATION	26
STEP 15 Connect power	27
OPTION A TYPICAL WIRING	27
OPTION B PERMANENT WIRING	27
STEP 16 Ensure the safety reversing sensors are aligned	29
Adjustments	30
Introduction	30
One-Piece Doors Only	30
Programming Buttons	30
STEP 1 Program the Travel	31
STEP 2 Test the Safety Reversal System	32
STEP 3 Test the Protector System®	32
Battery Backup	33
STEP 1 Install the Battery	33
STEP 2 Test the Battery	33
Charge the Battery	34
Battery status LED	34
Operation	35
Features	36
Using your Garage Door Opener	37
Using the Motion Detecting Control Panel	37
Using the Smart Control Panel	38
Remote Control	40
To Erase the Memory	41
To Open the Door Manually	41
Maintenance	42
Maintenance Schedule	42
The Remote Control Battery	42
Troubleshooting	43
Diagnostic Chart	43
Accessories	45
Warranty	46
Contact Information	46
Repair Parts	47
Rail Assembly Parts	47
Accessories	47
Installation Parts	47
Garage Door Opener Parts	48