Home » Cisco Manuals » Bridges & Routers » Cisco 7246 » Manual Viewer

Cisco 7246 Hardware Installation Guide - Page 66

Site Preparation Checklist

Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Site Preparation Checklist Chapter 2 Preparing the Cisco uBR7200 Series Router for Installation Site Preparation Checklist Before installing the Cisco uBR7200 series router, assemble the equipment needed to support your network configuration and subscriber service offering. Ensure all power and cabling requirements are met based on the equipment to be installed. Also ensure that environmental conditions are met to maintain proper equipment operation. Table 2-2 is a checklist that identifies the key tasks to complete. Table 2-2 Site Preparation Checklist Task Verified By Date General: Safety recommendations and guidelines reviewed. Required general CMTS preparations completed. Site power voltages verified. Site environmental specifications verified. Downstream and upstream channel plans created. Cable plant balanced, swept and verified to comply with DOCSIS or EuroDOCSIS recommendations. Optical receivers adjusted for proper upstream RF output levels. Required passwords, IP addresses, device names available. All additional CMTS equipment to support Internet access services, including upconverter and all other RF-related equipment, servers and other host computers, a Cisco uBR900 series cable access router, and console accessory kit to test operation of your network. Required tools and cables available. Telco Return Configurations: Telco return dial-up plan created. Network access server installed and configured. Telephone circuits, connections, and all equipment to support telco return. IP Telephony Configurations: Gatekeeper and gateway equipment installed and configured. Dial plan based on the supported VoIP protocol used-H.323 or SGCP. 2-20 Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide OL-5421-03

Section	Page
Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide	1
Contents	3
Preface	9
Cisco uBR7200 Series Overview	19
Cisco uBR7200 Series Universal Broadband Router	19
Cisco uBR7246 Router	21
Cisco uBR7246VXR Router	21
Cisco uBR7200 Series Network Interface Overview	23
Card Slot and Logical Interface Numbering	23
Cisco uBR7246	24
Cisco uBR7246VXR	24
MAC-Layer Address	25
Supported System Configurations Overview	26
Basic Internet Access Services	26
VPN Services	28
IP Telephony Services	29
Telco Return	29
Hardware Component Descriptions	30
Network Processing Engine	31
NPE Comparisons	31
Input/Output Controller	33
Cisco Cable Interface Line Cards	35
Cisco Cable Clock Card (Cisco uBR7246VXR Only)	35
Cisco Port Adapters	36
Cisco Port Adapter-Chassis-Release Matrix	36
Power Supplies	39
Fan Trays	41
Cisco uBR7246 and Cisco uBR7246VXR Chassis	43
Subchassis and Midplane	44
Cisco uBR7246VXR and Cisco uBR7246 Subchassis	44
Flash Memory Cards	45
CompactFlash Disk	46
Preparing the Cisco uBR7200 Series Router for Installation	47
Safety Recommendations	47
Lifting the Cisco uBR7200 Series Router Safely	48
Safety with Electricity	49
Preventing Electrostatic Discharge Damage	50
Site Requirements	51
AC Power	51
DC Power	52
Site Environment	52
Site Configuration: Maintaining Normal Operation	52
General Precautions	53
Power Considerations	53
Required Network Information	53
Before You Begin	54
Installation Tools	54
Rack-Mount and Cable-Management Kit	55
Equipment Required to Verify Your Plant’s RF Setup	55
Shipping Container Contents	56
Verifying the Shipping Container Contents	57
Provisioning the Cable Headend	57
Two-Way Data and VoIP	57
Headend Certification	58
IF-to-RF Upconverter	58
Diplex Filters	59
Receivers	59
DHCP, DNS, TFTP, and TD Servers	60
Telco Return	60
Dial-Up/Remote Access Servers	60
RADIUS Dial Security Servers	60
Authentication, Authorization, and Accounting Servers	61
VoIP Gateways and Gatekeepers	61
VoIP SGCP Pass-Through	61
Headend Wiring	62
Interference Considerations	62
Distance Limitations and Interface Specifications	62
Equipment Racks	63
Site Preparation Checklist	66
Component Checklists	67
Cisco uBR7246 and Cisco uBR7246VXR Component List	67
Installing the Cisco uBR7200 Series Router	69
Cisco uBR7200 Series Router Installation Checklist	69
Cisco uBR7200 Series Chassis Rack-Mounting Options	70
Cable-Management Bracket Requirements	73
Installing the Brackets on the Chassis	75
Installing Rack-Mount Brackets on the Rear of the Chassis	75
Installing Rack-Mount Brackets on the Front of the Chassis	76
Installing Rack-Mount Brackets in the Middle of the Chassis	78
Installing the Chassis in the Rack	79
Installing the Chassis in a Workbench or Tabletop Environment	81
Installing the Cable-Management Bracket on a Cisco uBR7200 Series Router in a Workbench or Tabletop Environment	82
Cabling	82
Connecting Port Adapter Cables	82
Connecting Cisco Cable Clock Card Cables (Cisco uBR7246VXR Only)	83
Connecting Cable Interface Line Card Cables	83
Connecting I/O Controller Cables	83
Console and Auxiliary Port Connection Equipment	84
Console Port Signals	85
Auxiliary Port Signals	86
Fast Ethernet MII Connection Equipment	86
Connecting Power	89
Connecting to the AC-Input Power Supply	90
Connecting to the DC-Input Power Supply	91
Powering On the Cisco uBR7200 Series Router	93
Configuring the Interfaces	95
Connecting the Cisco uBR7200 Series Router to the Cable Headend	97
Two-Way Data Headend Architecture	98
One-Way Data Headend Architecture	99
RF and Digital Data Overview	99
Connecting and Configuring the Downstream	100
Installing and Configuring the Upconverter	100
Setting the North American Upconverter Input Level	101
Setting the European Upconverter Input Level	102
Setting the Upconverter Output Level	102
Testing the Upconverter Output Level	103
Setting the Upconverter Output Frequency	103
Measuring Upconverter Phase Noise Contribution	104
Viewing the Downstream IF Signal	104
Viewing the RF Output Signal	107
Fine-Tuning the Center Frequencies	109
Completing the Downstream Configuration	111
Testing the Downstream Configuration	112
Measuring the Downstream RF Signal	112
Measuring the Downstream RF Signal Using the Channel Power Option on a Spectrum Analyzer	113
Measuring the Downstream IF Signal at the Cisco uBR7200 Series Router	113
Measuring the Downstream RF Signal at the Upconverter Output	115
Measuring the Downstream RF Signal Using CATV Mode on a Spectrum Analyzer	119
Measuring the Downstream IF Signal at the Cisco uBR7200 Series Router Using CATV Mode	119
Measuring the Downstream RF Signal at the Upconverter Output Using CATV Mode	122
Connecting and Configuring the Upstream	126
Connecting the Upstream to the Optical Receiver	126
Testing the Upstream Configuration	127
Measuring the Upstream RF Signal	130
Measuring the Upstream RF Signal Using a Spectrum Analyzer	130
Analyzing the Upstream RF Signal	133
Using the Zero-Span Method with Adjacent Upstream Channels	136
Measuring the RF Signal at the Forward Test Point on a Laser Transmitter	145
Configuring the Digital Signal	148
Maintaining the Cisco uBR7200 Series Router	151
Online Insertion and Removal	151
Environmental Monitoring and Reporting Functions	152
Environmental Monitoring	153
Reporting Functions	154
Fan Failures	157
Flash Memory Card	157
Installing a Flash Memory Card	157
Removing a Flash Memory Card	158
Formatting a New Flash Memory Card	159
Copying a Bootable Image onto a Flash Memory Card	160
Copying Bootable Images Between Flash Memory Cards	161
Not Enough Memory on the Flash Memory Card	161
Adding a New Image to the Flash Memory Card	162
Reformatting a Flash Memory Card	162
Troubleshooting	165
Overview	165
Providing Information	165
Problem Solving with Subsystems	166
Identifying Startup Problems	167
Power Subsystem	169
Cooling Subsystem	169
Processor Subsystem	170
Troubleshooting the I/O Controller	170
Troubleshooting the Network Processing Engine	171
Troubleshooting Port Adapters	172
Troubleshooting the Cisco Cable Clock Card (Cisco uBR7246VXR Only)	172
Troubleshooting Cable Interface Line Cards	173
Other Troubleshooting Information Websites	173
About Verifying the Downstream Signal	174
Cisco uBR7200 Series Router Specifications	177
Cisco uBR7246 Physical and System Specifications	177
Cisco uBR7246VXR Physical and System Specifications	179
RF Specifications	181
DOCSIS 1.0 Transmission Characteristics	182
Downstream RF Channel Transmission Characteristics	182
Upstream RF Channel Transmission Characteristics	183
DOCSIS 1.1 Transmission Characteristics	184
Downstream RF Channel Transmission Characteristics	184
Upstream RF Channel Transmission Characteristics	185
EuroDOCSIS Transmission Characteristics	185
Downstream RF Channel Transmission Characteristics	185
Upstream RF Channel Transmission Characteristics	187
Electrical Input and Output	187
Cable Specifications	189
Coaxial Cables	189
Console and Auxiliary Port Cables and Pinouts	190
Identifying an RJ-45 Rollover Cable	190
Console Port Cables and Pinouts	191
Auxiliary Port Cables and Pinouts	192
Fast Ethernet Port Cables and Pinouts	192
Identifying an RJ-45 Crossover Cable	192
Identifying an RJ-45 Straight-Through Cable	193
Fiber-Optic Cables and Connectors	194
Industry-Standard Wiring Plans	195
About Wiring Standards	195
TIA/EIA Standards Information	196
Optical Fiber Color Codes	197
Telephone Wire Color Codes	197
Frequency Allocation Tables	201
Standards Comparisons	202
NTSC Cable Television Channels and Relative Frequencies	203
NTSC (M) Cable Television Frequencies for Japan	208
PAL/SECAM Cable Television Channels and Relative Frequencies	210
Manufacturers for Headend Provisioning Requirements	215
North American Channel Plans	215
European Channel Plans	217
Site Log	219
Glossary	221