Home » Cisco Manuals » Bridges & Routers » Cisco 7304 » Manual Viewer

Cisco 7304 Installation Guide - Page 31

NSE-150 Memory Information - router through port

UPC - 746320850405

Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Chapter 2 NSE-150 Overview NSE-150 Memory Information • NVRAM for storing the system configuration and environmental monitoring logs. NVRAM uses a lithium battery to maintain its contents when disconnected from power. • Non-upgradeable boot ROM provides a "golden copy" of the default ROMmon image. • Auxiliary port with full data terminal equipment (DTE) functionality • Console port with full data communications equipment (DCE) functionality NSE-150 Memory Information To determine the memory configuration of your NSE-150, use the show version command. The following example shows an NSE-150 installed in a Cisco 7304 router: Router# show version Cisco IOS Software, 7300 Software (C7300-JS-M), Version 12.2(31)SB Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Thu 13-Jul-06 05:34 by wsatchel ROM: System Bootstrap, Version 12.2(20060308:003941) 7304-R1 uptime is 1 day, 14 hours, 58 minutes Uptime for this control processor is 1 day, 14 hours, 58 minutes System returned to ROM by power-on System restarted at 23:01:36 PDT Sun Jul 16 2006 System image file is "disk0:c7300-js-mz.v122_31_sb_oib_throttle-060712" cisco 7300 (NSE150) processor (revision 0x00) with 2064383K/32768K bytes of memory. Processor board ID SMQ0908N06Z SB-1 CPU at 800Mhz, Implementation 0x401, Rev 0.2, 512KB L2 Cache 4 slot midplane, Version 67.49 Last reset from power-on PXF processor tmc0 'system:pxf/ucode1' is running ( v1.0 ). PXF processor tmc1 'system:pxf/ucode1' is running ( v1.0 ). 5 FastEthernet interfaces 5 Gigabit Ethernet interfaces 5 Packet over SONET interfaces 2045K bytes of non-volatile configuration memory. 62592K bytes of ATA compact flash in bootdisk (Sector size 512 bytes). 125184K bytes of ATA compact flash in disk0 (Sector size 512 bytes). Configuration register is 0x0 Table 2-1 provides memory specifications and Table 2-2 provides user-replaceable memory configuration information for the NSE-150. Table 2-1 NSE-150 Memory Specifications Memory Type Memory Size DRAM 2 GB SDRAM 2GB Non-upgradeable boot 512 KB ROM Upgradeable boot ROM 2 MB Quantity 2 1 1 Description 2 1-GB SODIMMs1 built-in SDRAM SODIMMs OTP ROM for the ROM monitor (ROMmon) 2 Programmable ROM OL-3967-01 Cisco 7304 Network Service Engine Installation and Configuration 2-5

Section	Page
Cisco 7304 Network Service Engine Installation and Configuration	1
Contents	3
Preface	7
Objectives	7
Organization	7
Related Documentation	8
Obtaining Documentation	9
Cisco.com	9
Product Documentation DVD	9
Ordering Documentation	9
Documentation Feedback	10
Cisco Product Security Overview	10
Reporting Security Problems in Cisco Products	10
Product Alerts and Field Notices	11
Obtaining Technical Assistance	11
Cisco Technical Support & Documentation Website	11
Submitting a Service Request	12
Definitions of Service Request Severity	12
Obtaining Additional Publications and Information	13
NSE-100 Overview	15
Supported Platforms	15
NSE-100 Description	15
NSE-100 Hardware MAC Addresses Filtering	15
Interfaces and LEDs	16
Components	17
System Management Functions	19
NSE-100 Memory Information	19
Memory Systems Overview	19
Memory Specifications	20
Memory Locations	22
Determining the Memory Configuration	23
Gigabit Ethernet GBIC Port and Cabling Specifications	24
Mode-Conditioning Patch Cord Description	25
CWDM GBIC Modules	26
Fast Ethernet Management Port Connections	26
NSE-150 Overview	27
Supported Platforms	27
NSE-150 Description	27
LEDs	27
Components	29
NSE-150 Memory Information	31
Gigabit Ethernet SFP Port and Cabling Specifications	32
Master List of Supported SFP Modules	32
CWDM SFP Modules	33
1000BASE-T SFP Module	34
Optical Gigabit Ethernet 1000BASE-SX SFP Modules	34
Optical Gigabit Ethernet 1000BASE-LX/LH SFP Modules	34
Optical Gigabit Ethernet 1000BASE-ZX SFP Modules	35
Optical Gigabit Ethernet 1000BASE-BX SFP Modules	35
USB Interface	36
Fast Ethernet Management Port Connections	36
Console and Auxiliary Ports	36
Preparation for Installation	39
Required Tools and Equipment	39
Software Requirements	39
Bandwidth Oversubscription	40
Safety Guidelines	40
Safety Warnings	41
Class 1 and Class 1M Laser Warning	44
Backplane Voltage Warning	45
Faceplates and Cover Panel Requirement	46
Lightning Activity Warning	47
Radiation from Open Port Aperture	48
Battery Handling Warning	49
Electrical Equipment Guidelines	50
Telephone Wiring Guidelines	50
Electrostatic Discharge Prevention	50
Removing and Installing the NSE	53
Ensuring Easy Access to the Router	53
Powering Down the Router and Disconnecting Input Power	54
Powering Down an AC-Input Power Supply	54
Powering Down a DC-Input Power Supply and Removing the DC-Input Leads	55
Removing the Network Services Engine	56
Removing the Slot Divider for a Redundant Configuration	57
Inserting the Network Services Engine	59
Removing and Replacing the SDRAM SODIMM	60
Removing a SDRAM SODIMM on the NSE-100	61
Inserting a SDRAM SODIMM on the NSE-100	62
Installing and Using the CompactFlash Disk	63
Product Description	63
Installing and Removing the CompactFlash Disk	65
About GBIC Modules (NSE-100)	65
Installing and Removing the GBIC Modules and Cables	66
Attaching Multimode and Single-Mode Optical Fiber Cables	67
Attaching the Mode-Conditioning Patch Cord	69
Installing and Removing SFP Modules (NSE-150)	69
Installing and Removing the CWDM GBIC and SFP Modules	70
Connecting the Fast Ethernet 10/100 Cable to the Fast Ethernet Management Port	70
Intra-Building Lightning Protection	71
Attaching the Console Port and Auxiliary Port Cables	71
Reconnecting Input Power and Powering Up the Router	71
Reconnecting AC-Input Power	71
Reconnecting DC-Input Power	72
Powering Up the Router	74
Verifying a Successful Boot	74
High Availability NSE Redundancy	77
High Availability System Requirements	77
High Availability Commands	78
FPGA Upgrades and Failover	79
GBIC Module, SFP Module, and FE Management Port Addressing	79
CompactFlash Disk Commands	79
Working with a CompactFlash Disk	81
Software Command Overview	81
Using Software Commands	83
Using the show Command	83
Using the pwd Command	84
Using the cd Command	84
Using the dir Command	85
Using the format Command	85
Using the copy Command	86
Using the mkdir Command	87
Using the rmdir Command	88
Using the delete Command	88
Enabling Booting from a CompactFlash Disk	89
Boot Environment Variables	90
Making a CompactFlash Disk-Based Software Image the Bootable Software Image	91
Upgrading, Configuration, and Troubleshooting Tasks	93
Configuration Tasks	93
Upgrading FPGA	94
FPGA Recovery Upgrade on the NSE-150	94
Upgrading ROMmon	94
Using the show rom-monitor Command	94
Using the upgrade rom-monitor Command	95
Troubleshooting ROMmon Upgrades	96
Additional ROMmon Upgrade Information	96
Configuring Autoboot to Boot from the Network	96
Configuring Autoboot to Boot from a Local Device	96
Using the Bootldr Command	96
Failure to Boot After a SDRAM Upgrade or Replacement	97
Using the show version Command	97
Using the show c7300 Command	98
Using the show c7300 pxf accounting or show pxf Command	99
Using Debugging Commands and PXF	99
Ethernet Pause Frames on the NSE Gigabit Ethernet Ports	99
Troubleshooting	100

Match case Limit results 1 per page

2-5

Cisco 7304 Network Service Engine Installation and Configuration

OL-3967-01

Chapter 2

NSE-150 Overview

NSE-150 Memory Information

•

NVRAM for storing the system configuration and environmental monitoring logs. NVRAM uses a

lithium battery to maintain its contents when disconnected from power.

•

Non-upgradeable boot ROM provides a “golden copy” of the default ROMmon image.

•

Auxiliary port with full data terminal equipment (DTE) functionality

•

Console port with full data communications equipment (DCE) functionality

NSE-150 Memory Information

To determine the memory configuration of your NSE-150, use the

show version

command.

The following example shows an NSE-150 installed in a Cisco 7304 router:

Router#

show version

Cisco IOS Software, 7300 Software (C7300-JS-M), Version 12.2(31)SB

Compiled Thu 13-Jul-06 05:34 by wsatchel

ROM: System Bootstrap, Version 12.2(20060308:003941)

7304-R1 uptime is 1 day, 14 hours, 58 minutes

Uptime for this control processor is 1 day, 14 hours, 58 minutes

System returned to ROM by power-on

System restarted at 23:01:36 PDT Sun Jul 16 2006

System image file is "disk0:c7300-js-mz.v122_31_sb_oib_throttle-060712"

cisco 7300 (NSE150) processor (revision 0x00) with 2064383K/32768K bytes of memory.

Processor board ID SMQ0908N06Z

SB-1 CPU at 800Mhz, Implementation 0x401, Rev 0.2, 512KB L2 Cache

4 slot midplane, Version 67.49

Last reset from power-on

PXF processor tmc0 'system:pxf/ucode1' is running ( v1.0 ).

PXF processor tmc1 'system:pxf/ucode1' is running ( v1.0 ).

5 FastEthernet interfaces

5 Gigabit Ethernet interfaces

5 Packet over SONET interfaces

2045K bytes of non-volatile configuration memory.

62592K bytes of ATA compact flash in bootdisk (Sector size 512 bytes).

125184K bytes of ATA compact flash in disk0 (Sector size 512 bytes).

Configuration register is 0x0

Table 2-1

provides memory specifications and

Table 2-2

provides user-replaceable memory

configuration information for the NSE-150.

Table 2-1

NSE-150 Memory Specifications

Memory Type

Memory Size

Quantity

Description

DRAM

2 GB

2 1-GB SODIMMs

SDRAM

2GB

built-in SDRAM SODIMMs

Non-upgradeable boot

ROM

512 KB

OTP ROM for the ROM monitor (ROMmon)

Upgradeable boot

ROM

2 MB

Programmable ROM