Home » Cisco Manuals » Bridges & Routers » Cisco 7304 » Manual Viewer

Cisco 7304 Installation Guide - Page 51

Handling a Network Services Engine-Side View

UPC - 746320850405

Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Chapter 3 Preparation for Installation Figure 3-1 Handling a Network Services Engine-Side View 1 Safety Guidelines 2 66427 1 Metal carrier 2 Printed circuit board Although the metal carrier helps to protect the printed circuit boards from ESD, wear a preventive antistatic strap whenever handling a network services engine. Ensure that the strap makes good skin contact and connect the strap's clip to an unpainted chassis surface to channel unwanted ESD voltages safely to ground. If no wrist strap is available, ground yourself by touching the metal part of the chassis. Caution Make sure to tighten the captive installation screws on the network services engine (use a number 2 Phillips or a 3/16-inch flat-blade screwdriver). These screws prevent accidental removal, provide proper grounding for the router, and help to ensure that the network services engine is properly seated in the router midplane. Following are guidelines for preventing ESD damage: • Always use an ESD wrist strap or ankle strap when installing or replacing the network services engine. Ensure that the ESD strap makes contact with your skin. • Handle the network services engine by its metal carrier edges and handles only; avoid touching the printed circuit board components or any connector pins. • When removing the network services engine, place it on an antistatic surface with the printed circuit board components facing upward, or in a static shielding bag. If you are returning a network services engine to the factory, immediately place it in a static shielding bag. Caution Periodically check the resistance value of the antistatic strap. The measurement should be within the range of 1 to 10 megohms (Mohms). OL-3967-01 Cisco 7304 Network Service Engine Installation and Configuration 3-13

Section	Page
Cisco 7304 Network Service Engine Installation and Configuration	1
Contents	3
Preface	7
Objectives	7
Organization	7
Related Documentation	8
Obtaining Documentation	9
Cisco.com	9
Product Documentation DVD	9
Ordering Documentation	9
Documentation Feedback	10
Cisco Product Security Overview	10
Reporting Security Problems in Cisco Products	10
Product Alerts and Field Notices	11
Obtaining Technical Assistance	11
Cisco Technical Support & Documentation Website	11
Submitting a Service Request	12
Definitions of Service Request Severity	12
Obtaining Additional Publications and Information	13
NSE-100 Overview	15
Supported Platforms	15
NSE-100 Description	15
NSE-100 Hardware MAC Addresses Filtering	15
Interfaces and LEDs	16
Components	17
System Management Functions	19
NSE-100 Memory Information	19
Memory Systems Overview	19
Memory Specifications	20
Memory Locations	22
Determining the Memory Configuration	23
Gigabit Ethernet GBIC Port and Cabling Specifications	24
Mode-Conditioning Patch Cord Description	25
CWDM GBIC Modules	26
Fast Ethernet Management Port Connections	26
NSE-150 Overview	27
Supported Platforms	27
NSE-150 Description	27
LEDs	27
Components	29
NSE-150 Memory Information	31
Gigabit Ethernet SFP Port and Cabling Specifications	32
Master List of Supported SFP Modules	32
CWDM SFP Modules	33
1000BASE-T SFP Module	34
Optical Gigabit Ethernet 1000BASE-SX SFP Modules	34
Optical Gigabit Ethernet 1000BASE-LX/LH SFP Modules	34
Optical Gigabit Ethernet 1000BASE-ZX SFP Modules	35
Optical Gigabit Ethernet 1000BASE-BX SFP Modules	35
USB Interface	36
Fast Ethernet Management Port Connections	36
Console and Auxiliary Ports	36
Preparation for Installation	39
Required Tools and Equipment	39
Software Requirements	39
Bandwidth Oversubscription	40
Safety Guidelines	40
Safety Warnings	41
Class 1 and Class 1M Laser Warning	44
Backplane Voltage Warning	45
Faceplates and Cover Panel Requirement	46
Lightning Activity Warning	47
Radiation from Open Port Aperture	48
Battery Handling Warning	49
Electrical Equipment Guidelines	50
Telephone Wiring Guidelines	50
Electrostatic Discharge Prevention	50
Removing and Installing the NSE	53
Ensuring Easy Access to the Router	53
Powering Down the Router and Disconnecting Input Power	54
Powering Down an AC-Input Power Supply	54
Powering Down a DC-Input Power Supply and Removing the DC-Input Leads	55
Removing the Network Services Engine	56
Removing the Slot Divider for a Redundant Configuration	57
Inserting the Network Services Engine	59
Removing and Replacing the SDRAM SODIMM	60
Removing a SDRAM SODIMM on the NSE-100	61
Inserting a SDRAM SODIMM on the NSE-100	62
Installing and Using the CompactFlash Disk	63
Product Description	63
Installing and Removing the CompactFlash Disk	65
About GBIC Modules (NSE-100)	65
Installing and Removing the GBIC Modules and Cables	66
Attaching Multimode and Single-Mode Optical Fiber Cables	67
Attaching the Mode-Conditioning Patch Cord	69
Installing and Removing SFP Modules (NSE-150)	69
Installing and Removing the CWDM GBIC and SFP Modules	70
Connecting the Fast Ethernet 10/100 Cable to the Fast Ethernet Management Port	70
Intra-Building Lightning Protection	71
Attaching the Console Port and Auxiliary Port Cables	71
Reconnecting Input Power and Powering Up the Router	71
Reconnecting AC-Input Power	71
Reconnecting DC-Input Power	72
Powering Up the Router	74
Verifying a Successful Boot	74
High Availability NSE Redundancy	77
High Availability System Requirements	77
High Availability Commands	78
FPGA Upgrades and Failover	79
GBIC Module, SFP Module, and FE Management Port Addressing	79
CompactFlash Disk Commands	79
Working with a CompactFlash Disk	81
Software Command Overview	81
Using Software Commands	83
Using the show Command	83
Using the pwd Command	84
Using the cd Command	84
Using the dir Command	85
Using the format Command	85
Using the copy Command	86
Using the mkdir Command	87
Using the rmdir Command	88
Using the delete Command	88
Enabling Booting from a CompactFlash Disk	89
Boot Environment Variables	90
Making a CompactFlash Disk-Based Software Image the Bootable Software Image	91
Upgrading, Configuration, and Troubleshooting Tasks	93
Configuration Tasks	93
Upgrading FPGA	94
FPGA Recovery Upgrade on the NSE-150	94
Upgrading ROMmon	94
Using the show rom-monitor Command	94
Using the upgrade rom-monitor Command	95
Troubleshooting ROMmon Upgrades	96
Additional ROMmon Upgrade Information	96
Configuring Autoboot to Boot from the Network	96
Configuring Autoboot to Boot from a Local Device	96
Using the Bootldr Command	96
Failure to Boot After a SDRAM Upgrade or Replacement	97
Using the show version Command	97
Using the show c7300 Command	98
Using the show c7300 pxf accounting or show pxf Command	99
Using Debugging Commands and PXF	99
Ethernet Pause Frames on the NSE Gigabit Ethernet Ports	99
Troubleshooting	100

Match case Limit results 1 per page

3-13

Cisco 7304 Network Service Engine Installation and Configuration

OL-3967-01

Chapter 3

Preparation for Installation

Safety Guidelines

Figure 3-1

Handling a Network Services Engine—Side View

Although the metal carrier helps to protect the printed circuit boards from ESD, wear a preventive

antistatic strap whenever handling a network services engine. Ensure that the strap makes good skin

contact and connect the strap’s clip to an unpainted chassis surface to channel unwanted ESD voltages

safely to ground.

If no wrist strap is available, ground yourself by touching the metal part of the chassis.

Caution

Make sure to tighten the captive installation screws on the network services engine (use a number 2

Phillips or a 3/16-inch flat-blade screwdriver). These screws prevent accidental removal, provide proper

grounding for the router, and help to ensure that the network services engine is properly seated in the

router midplane.

Following are guidelines for preventing ESD damage:

•

Always use an ESD wrist strap or ankle strap when installing or replacing the network services

engine. Ensure that the ESD strap makes contact with your skin.

•

Handle the network services engine by its metal carrier edges and handles only; avoid touching the

printed circuit board components or any connector pins.

•

When removing the network services engine, place it on an antistatic surface with the printed circuit

board components facing upward, or in a static shielding bag. If you are returning a network services

engine to the factory, immediately place it in a static shielding bag.

Caution

Periodically check the resistance value of the antistatic strap. The measurement should be within the

range of 1 to 10 megohms (Mohms).

Metal carrier

Printed circuit board

66427