Cisco SA520-K9 Quick Start Guide - Page 2

3 Installation Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R) © 2009 Cisco Systems, Inc. All rights reserved. Printed in the USA on recycled paper containing 10% postconsumer waste. 78-18996-02 STEP 1 Connect the security appliance to power. STEP 2 If you are installing the SA520W, screw each antenna onto a threaded connector on the back panel. Orient each antenna to point upward. STEP 3 For DSL, a cable modem, or other WAN connectivity devices, connect an Ethernet network cable from the device to the WAN port on the back panel. Cisco strongly recommends using Cat5E or better cable. STEP 4 For network devices, connect an Ethernet network cable from the network device to one of the dedicated LAN ports on the back panel. STEP 5 For a UC500, connect an Ethernet network cable from the WAN port of the UC500 to an available LAN port of the security appliance. For details about configuring the UC500 and the security appliance to work together, see the SA500 Series Security Appliances Administration Guide on Cisco.com. See the documentation links in the "Where to Go From Here" section of this guide. STEP 6 Power on the security appliance. STEP 7 Power on the connected devices. Each LED lights to show an active connection. A sample configuration is illustrated below. Congratulations! The installation of the security appliance is complete. 4 Launching the Configuration Utility STEP 1 Connect your PC to an available LAN port on the back panel of the security appliance. Your PC will become a DHCP client of the security appliance and will receive an IP address in the 192.168.75.x range. STEP 2 Start a web browser. In the Address bar, enter the default IP address of the security appliance: 192.168.75.1. You can use Internet Explorer (version 6 and higher), Firefox, and Safari (for Mac). STEP 3 When the Security Alert appears, accept or install the certificate: • Internet Explorer: Click Yes to proceed, or click View Certificate for details. On the Certificate page, click Install the Certificate. Follow the instructions in the Wizard to complete the installation. • Firefox: Click the link to add an exception. Click the Add Exception button. Click Get Certificate, and then click Confirm Security Exception. • Safari: Click Continue to proceed, or click Show Certificate. On the Certificate page, click Install the Certificate. Follow the instructions in the Wizard to complete the installation. STEP 4 When the login page appears, enter the user name and password. The default user name is cisco. The default password is cisco. Passwords are case sensitive. STEP 5 Click Login. The Getting Started page of the Configuration Utility appears. NOTE You also can launch the Configuration Utility from the Cisco Configuration Assistant (CCA) if a CCA-supported device is connected to your security appliance. For details, refer to your CCA documentation. 5 Getting Started with the Configuration The security appliance is pre-configured with default settings that allow you to begin using the device right away. However, you may wish to adjust these settings or enable special features. The Configuration Utility includes a Getting Started page that makes it easy to complete the most common configuration tasks. Typical tasks include: • Configure the WAN and LAN connectivity. • Upgrade the firmware. • Change the default administrator password. • Configure the security settings. • Configure the VPN connections. • Configure the wireless settings (SA520W). Click a link on the Getting Started page to choose a task that you want to perform. When the configuration page appears, enter the information, and then click Apply to save your settings. Click Getting Started in the menu bar to return to the Getting Started page. To configure features that are not included on the Getting Started page, you can use the buttons on the menu bar and the links in the navigation tree. NOTE For complete details about configuring your security appliance, refer to the SA500 Series Security Appliances Administration Guide on Cisco.com. See the documentation links in the "Where to Go From Here" section of this guide. 6 Where to Go From Here Support Cisco Small Business Support Community Online Technical Support and Documentation Cisco Small Business Support and Resources Phone Support Contacts Software Quick VPN Software Cisco VPN Client SA500 Firmware Downloads Product Documentation SA500 Technical Documentation Cisco Small Business Cisco Partner Central for Small Business (Partner Login Required) Cisco Small Business Home www.cisco.com/go/smallbizsupport www.cisco.com/support (Log in required) www.cisco.com/go/smallbizhelp www.cisco.com/go/sbsc www.cisco.com/go/qvpn www.cisco.com/go/ciscovpnclient www.cisco.com/go/sa500software www.cisco.com/go/sa500resources www.cisco.com/web/partners/sell/smb www.cisco.com/smb