Cisco SE2500 Getting Started Guide - Page 24

Step 3, verification and basic configuration as shown in the following bootup display example - manual

Get Cisco SE2500 PDF manuals and user guides View all Cisco SE2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Step 3 Observe the bootup using the CLI screen. The bootup script displays operating system software initialization (code download and POST verification) and basic configuration as shown in the following bootup display example: CISCO SYSTEMS WLCNG Boot Loader Version 1.0.15 (Built on Nov 23 2010 at 07:51:36 by cisco) Board Revision 0.0 (SN: PSJ143302MT, Type: AIR-CT2504-K9) (P) Verifying boot loader integrity... OK. OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate) CPU Cores: 4 DRAM: 1024 MB Flash: 32 MB Clearing DRAM........ done Network: octeth0', octeth1, octeth2, octeth3 ' - Active interface E - Environment MAC address override CF Bus 0 (IDE): OK IDE device 0: - Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C181101244A1Yb3A5QNU - Type: Hard Disk - Capacity: 977.4 MB = 0.9 GB (2001888 x 512) Press now to access the Boot Menu... Continue booting the controller or press Esc to access the following menu Boot Loader Menu 1. Run primary image (7.0.114.76) - Active 2. Run backup image (7.0.114.75) 3. Change active boot image 4. Clear configuration 5. Format FLASH Drive 6. Manually update images Enter selection: If you did not press Esc, the boot process continues and takes two to three minutes. Do not reboot the controller until the user login prompt appears. Loading primary image (7.0.114.76) 100% 31427987 bytes read Launching images... init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary starting pid 672, tty '': '/etc/init.d/rcS' type = block dump-device = 254:4 disrupt level = header 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
24
Step 3
Observe the bootup using the CLI screen.
The bootup script displays operating system software initialization (code download and POST
verification) and basic configuration as shown in the following bootup display example:
CISCO SYSTEMS
WLCNG Boot Loader Version 1.0.15 (Built on Nov 23 2010 at 07:51:36 by cisco)
Board Revision 0.0 (SN: PSJ143302MT, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data
rate)
CPU Cores:
4
DRAM:
1024 MB
Flash: 32 MB
Clearing DRAM
........
done
Network: octeth0', octeth1, octeth2, octeth3
' - Active interface
E - Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
- Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C181101244A1Yb3A5QNU
- Type: Hard Disk
- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
Press <ESC> now to access the Boot Menu...
Continue booting the controller or press Esc to access the following menu:
============================================================
Boot Loader Menu
============================================================
1. Run primary image (7.0.114.76) - Active
2. Run backup image (7.0.114.75)
3. Change active boot image
4. Clear configuration
5. Format FLASH Drive
6. Manually update images
------------------------------------------------------------
Enter selection:
If you did not press
Esc
, the boot process continues and takes two to three
minutes. Do not reboot the controller until the user login prompt appears.
Loading primary image (7.0.114.76)
100%
31427987 bytes read
Launching images...
init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary
starting pid 672, tty '': '/etc/init.d/rcS'
type = block
dump-device = 254:4
disrupt
level = header