Cisco SFE2000 Administration Guide - Page 54

Port Configuration, System Mode (Layer 2 / Layer 3) Selection, On the Switch Main Menu screen

Get Cisco SFE2000 - Small Business Managed Switch PDF manuals and user guides
UPC - 745883572106
View all Cisco SFE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Chapter 2. Press the Enter key. The Port Status screen displays the port numbers, their status, Link status, speed and duplex mode, and status of flow control, which is the flow of packet transmissions. If you want to change any settings for a port, you must use the Port Configuration screen. Port Configuration The Port Configuration screen lets you specify the auto negotiation status, port speed, duplex mode, and flow control settings. To configure the ports: 1. On the Switch Main Menu screen, select Port Configuration. 2. Press the Enter key. The Port Configuration screen displays the port numbers, their status, auto-negotiation status, speed and duplex mode, and status of flow control, which is the flow of packet transmissions. 3. Select Edit to make changes. When your changes are complete, press the Esc key to return to the Action menu. 4. Select Save to save your changes. System Mode (Layer 2 / Layer 3) Selection The System Mode Selection screen lets you specify whether the Ethernet switch is operating in Layer 2 or Layer 3 mode. You can also configure stacking mode from this screen. IMPORTANT: If the Ethernet switch is being used as part of a Linksys One system, it must operate as a Layer 2 switch. To view or edit the system mode: 1. On the Switch Main Menu screen, select System Mode (Layer 2 / Layer 3) Selection Port Configuration. 2. Press the Enter key. The System Mode (Layer 2 / Layer 3) Selection screen displays the current system and stacking mode. Linksys One Ready Communications Solution 4 TIP: Use the up or down arrow keys to scroll through all the ports on the Ethernet switch. 48 Chapter 4: Console Configuration Configuring the Switch through the Console or Telnet Interface

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Chapter
4
48
Chapter 4: Console Configuration
Configuring the Switch through the Console or Telnet Interface
Linksys One Ready Communications Solution
2.
Press the
Enter
key. The Port Status screen displays the port numbers, their status, Link
status, speed and duplex mode, and status of flow control, which is the flow of packet
transmissions.
If you want to change any settings for a port, you must use the Port Configuration screen.
Port Configuration
The Port Configuration screen lets you specify the auto negotiation status, port speed, duplex
mode, and flow control settings.
To configure the ports:
1.
On the Switch Main Menu screen, select Port Configuration.
2.
Press the
Enter
key. The Port Configuration screen displays the port numbers, their status,
auto-negotiation status, speed and duplex mode, and status of flow control, which is the
flow of packet transmissions.
3.
Select Edit to make changes. When your changes are complete, press the
Esc
key to
return to the Action menu.
4.
Select Save to save your changes.
System Mode (Layer 2 / Layer 3) Selection
The System Mode Selection screen lets you specify whether the Ethernet switch is operating
in Layer 2 or Layer 3 mode. You can also configure stacking mode from this screen.
To view or edit the system mode:
1.
On the Switch Main Menu screen, select System Mode (Layer 2 / Layer 3) Selection Port
Configuration.
2.
Press the
Enter
key. The System Mode (Layer 2 / Layer 3) Selection screen displays the
current system and stacking mode.
IMPORTANT:
If the Ethernet switch is
being used as part of a Linksys One
system, it must operate as a Layer 2
switch.
TIP:
Use the
up
or
down
arrow keys to
scroll through all the ports on the
Ethernet switch.