Clifford Concept 50 Owners Guide - Page 22

Matrix of user-selectable features Feature Select Column 1 Column 2 1st latched 2nd latched Column 3 3rd latched Column 4 4th latched Column 5 5th latched Column 6 6th latched Row 1 1st momentary Sound 1: on/off info on page 18 Add new remote to channel 1 (arm/disarm) info on page 9-10 & 23 NOTE 1 Test/adjust primary (normal) zone of vibration sensor info on pages 13-14 NOTE 7 QuietChirps: on/off info on page 18 Anti-carjacking: on/off info on page 7-8 Headlight timer: 1sec-2.5min (30sec) info on pages 11 & 17 NOTE 13 Row 2 2nd momentary Sound 2: on/off info on page 18 Add new remote to channel 2 (trunk/timer) info on page 9-10 & 23 NOTE 2 Test/adjust secondary (high) zone of vibration sensor info on pages 13-14 NOTE 8 Long-term chirp silencing: on/off info on page 18 Remote control button/channel sequence for anti-carjacking info on page 8 NOTE 10 RPM monitoring: on/off Row 3 3rd momentary Sound 3: on/off info on page 18 Add new remote to channel 3 (silent arm/disarm) info on page 9-10 & 23 NOTE 3 Test/adjust glass tampering sensor info on pages 13-14 NOTE 9 15-second entry delay: on/off info on page 12 Add a dedicated anti-carjacking remote control info on page 8 NOTE 11 Factory-delayed courtesy lights: on/off Row 4 4th momentary Add new remote to Sound 4: on/off channel 4 (accessory 1) info on page 18 info on page 9-10 & 23 NOTE 4 Pulsed/constant ground output upon panic AutoLock/UnLock: on/off info on page 17 Set idle RPM Channel 4 output: pulsed/latched/timed Row 5 5th momentary Add new remote to Sound 5: on/off channel 5 (accessory 2) Headlight Reminder: on/off info on page 18 info on page 9-10 & 23 info on page 16 NOTE 5 Smart AutoArming: on/off info on page 12 Siren duration: 30/60 sec. info on page 18 Channel 5 output: pulsed/latched/timed Row 6 6th momentary Sound 6: on/off info on page 18 Erase all channels info on page 9-10 & 23 NOTE 6 FACT: on/off info on page 15 AutoArm & Lock: on/off info on page 12 Set a new secret disarming/valet code info on pages 7-8 & 13 NOTE 12 QuickAccess valet mode: on/off info on page 16 Gray cells indicate features that require programming by trained Clifford installers. DO NOT change any of these setting. D WARNING: If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING; it requires installer-only adjustment. Changing the duration may cause damage. NOTE 1: Transmit channel 1 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 2: Transmit channel 2 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 3: Transmit channel 3 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 4: Transmit channel 4 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 5: Transmit channel 5 (or other channel of your choosing) of the new remote control. You will hear two chirps to indicate that the code has been accepted and recorded. NOTE 6: When you hear the two chirps, all remote control codes will have been erased from system memory. You must now add the new and/or existing remote controls to the system (i.e., program channels 1-5 of each remote that will be used with your Concept 50). NOTE 7: Turn off the ignition, exit the vehicle (taking the keys with you) and close the doors. Firmly "thump" the window pillar with the side of your fist. You should hear a chirp to confirm activation of the sensor's main zone. Use remote control button 2 to increase sensitivity, button 4 to decrease. Repeat until the sensor is set to the sensitivity you wish, then press remote control button 1 to end programming mode. NOTE 8: Use the same procedure as NOTE 7, but strike the window pillar lightly. NOTE 9: Use the same procedure as NOTE 7, but firmly tap a coin (such as a quarter) against the window to test sensitivity. NOTE 10: Transmit the first channel of your choice (any channel from 1-12). You will hear a one-chirp confirmation. Transmit the second channel of your choice (again, any channel you wish from 1-12). You will hear a two-chirp confirmation. You may now use this combination to turn off the 20-second anti-carjacking countdown. NOTE 11: Transmit the channel of your choice on the dedicated anti-carjacking remote control. You will hear two chirps to indicate that that remote control button will now turn off the 20-second anti-carjacking countdown. Be sure to carry this remote on your person, since a carjacker will undoubtedly take your usual remote control and purse. NOTE 12: Immediately flip the switch to its latched position, then enter the new code that you wish to use. Make sure to return the switch to its center position when complete, then wait 3 seconds (you will hear two chirps when the system has accepted the new code). Turn the ignition off. VERY IMPORTANT: You must immediately test your new secret disarming/valet code: Turn the ignition on, enter your new code, then flip the switch to its latched position. The LED will illuminate. If it does not, the new code you programmed and the one you just entered do not match. The system has reverted to the previous code. NOTE 13: The timer starts as soon as you enable this feature (6 latches, 1 momentary). When the duration you wish has been reached, press button 1 on the remote control. You will hear two chirps to confirm the new duration.