Cobra 29 LX BT Operating Instructions - Page 12

Operation Operation Setting the Once alarm settings are complete, rotate Menu/Enter Alarm continued knob clockwise to Set Snooze and press to select. B/ANL ANL NSoWteR 1.5 2 3 CAL TX EXIT SCAN CH 9/ 19 Default snooze time lengtRhX MEM SCAN SET SNOOZE S/RF SWR iRsF10 minutes. CB / WX DIM ALARM LENGTH CAL NSoItGe 1 3 5 7 9 +30dB Press Dim/Escape button tMoEN U SQreturn toDCYBNAstMaInKdEby mode. ESC PUESnHteENrTdEResirMedEMsnWoXo!ze time (from 1 to 60 minutes). Select Enter to eRxFitG, AreINturn toDESLeTAt STUnNoEoze ToBr AAClKarm SWR CAL Radio Check Mode Allows testing of important radio functions. Test 1- Battery Level: Confirms that battery voltage level is between 10.8 V to 15.8 V. If in that range, it is "PASS". Outside of that range, either FAIL LOW" or "FAIL HIGH" will be displayed. Press Menu/Enter knob to advance to next test. 1 Radio Check Mode Note Press Dim/Escape button to return to CB standby mode. If 10 seconds pass or if Enter button pressed, unit goes to 2nd test. Note Length. Select Alarm Length to set alarm duration Default alarm length (from 10 to 300 seconds). Pressing Menu/Enter is 60 seconds and is set in knob returns unit to exit, Set Snooze or Alarm MIN 10 second increments. Length. MIN MAX OFF 2 3 Setting the Setting the Count Down Timer Note Press Push-To-Talk within 10 Count Down To set the count down timer, press Menu/Enter seconds or unit will go to the Timer knob and select Set Count Down. NL L SWNRot1.e5 2 3 CAL TX SET CLOCK SCAN CH 9/ 19 F RF Press Dim/Escape buttRonX to R return to CB standby mode. SET ALARM SET COUNT DOWN MEM SCAN CB / WX DIM SIG SQ 1 3 5 7 9 +30dB DYNAMIKE ESC MENU PU SH FE NoTlElRow MEM WX ! instructions in Setting the Clock section (page 17) to sReFtGcAoINunt doDwENLnBT/AAhNLToUuNrEandT BACK SWR CAL NB /ANL minutes. Once desired count down time NB/ANL SWR ANL is1.5 2 3 CAL TX Test 2- RF Power Output: Confirms 3.3 to 4 Watt output level. Once Push-to-Talk button is pressed, Pass or Fail will be displayed if level is outside limits. 1 RF POWER OUTPUT 2 NB/ANL SWR 1.5 2 3 ANL CAL TX 3 RF SCAN CH 9/ PO19WER OUTPUT next test. Note Press Dim/Escape button to return to CB standby mode. If 10 seconds pass or if Enter button pressed, go to 3rd test. SCAN CH 9/ 19 MIN Key Tones KesaenyldeTcroteentdue,rsnprMteosostdhMeeesOntaunn/dEabnnytdemrOekfnnfoub. again to set Test 3- Antenna Mismatch Warning: Press MIN MAX S/ RF SWR /CAL S/RF SWR CAL RF SIG 1 OFF VOL SQ PASS FAIL S/RRXF S/RF RF SWR 3 5 79 +30SdW B R/CAL MENU CAL SIG PU SH ENTER DYNAMIKE VOL SQ RX MEM SCAN 1 MEM 35 WX ! 79 +30dB CB / WX / PA MENU PU SH ENTER MEM DYNRAFMGIKAEIN DELTA TUNE T BACK DIM ESC WX ! SRCW FALGRAIN DELTA TUNE MEM SCAN CB / WX / DIM PA ESC Note PTreBsAsCKDimSC/WAELRscape button to Mode Press Menu/Enter knob and rotate clockwise to Set Key Tones. Press Menu/Enter to set Key Push-to-Talk button to check antenna/radio for proper matching. return to CB standby mode. If 10 seconds pass or if Enter Note Tones On/Off. OFF MIN OFF 1 MINMIN MAX OFF MIN MAX buOFtFton pressed, testing is NB/ANPLress Dim/Escape buttoNBnA/NAtLNoL reStWuRrn1.5to 2CB 3mode.CAL TX SET KEY TONES SCAN CH 9/ 19 S/ RF SWR /CAL S/RF RF SWR CAL SIG 1 VOL SQ RX ON MEM SCAN OFF ANTENNA ANTENNA 3 5 7 9 +30dB Pe1xr8eitsstoMmeaniun/mEnetneur.knob to select On/Off and PASS FAIL DYNAMIKE MENU PU SH ENTER MEM WX ! RF GAIN NB /ANL CB / WX NB/ANL SWR 1.5 2 DIM NB/ANL 3 ESC CAL TX 2 NB/ANL SWR 1.5 2 3 CAL TX 3 SCAN CH 9/ 19 ANL ANL S/ RF S/RF RF DELTASTWURNE CAL SWR /CAL SIG T BACK 1 3 5 S/RRXF SWR CAL 7 9 +30SdW B R/CAL MENU S/RF RF SWR CAL SIG PU SH ENTER VOL SQ DYNAMIKE VOL SQ RX MEM SCAN 1 MEM 3 5 79 WX ! +30dB MENU PU SH CB / WX / PA ENTER MEM DYNRAFMGIKAEIN DELTA TUNE T BACK DIM ESC WX ! SRCW FALGRAIN complete. Unit will return to CB Standby mode. SCAN MEM SCAN CB / WX / PA CH 9/ 19 DIM ESC 19 DELTA TUNE T BACK SWR CAL OFF MIN MIN MAX OFF