Compaq Presario F700 HP G6000 Notebook PC and Compaq Presario F700 Notebook PC - Page 74

to lift the right side of the system board, When replacing the system board

Get Compaq Presario F700 - Notebook PC PDF manuals and user guides View all Compaq Presario F700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● Memory modules (see Memory module on page 42) ● RTC battery (see RTC battery on page 44) ● WLAN module (see WLAN module on page 45) ● Fan/heat sink assembly (see Fan/heat sink assembly on page 71) ● Processor (see Processor on page 73) Remove the system board: 1. Remove the two Phillips PM2.5×5.0 screws (1) that secure the system board to the base enclosure. 2. Flex the front edge of the base enclosure (2) forward until the audio connectors clear the openings in the base enclosure. 3. Use the optical drive connector (3) to lift the right side of the system board (4) until it rests at an angle. 4. Disconnect the audio board cable (1) from the system board. 5. Disconnect the USB board cable and power connector cable (2) from the system board. 66 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
Memory modules (see
Memory module
on page
42
)
●
RTC battery (see
RTC battery
on page
44
)
●
WLAN module (see
WLAN module
on page
45
)
●
Fan/heat sink assembly (see
Fan/heat sink assembly
on page
71
)
●
Processor (see
Processor
on page
73
)
Remove the system board:
1
.
Remove the two Phillips PM2.5×5.0 screws
(1)
that secure the system board to the base enclosure.
2
.
Flex the front edge of the base enclosure
(2)
forward until the audio connectors clear the openings
in the base enclosure.
3
.
Use the optical drive connector
(3)
to lift the right side of the system board
(4)
until it rests at an
angle.
4
.
Disconnect the audio board cable
(1)
from the system board.
5
.
Disconnect the USB board cable and power connector cable
(2)
from the system board.
66
Chapter
4
Removal and replacement procedures