Home » Compaq Manuals » Desktops » Compaq dc5850 » Manual Viewer

Compaq dc5850 Technical Reference Guide: HP Compaq dc5850 Series Business Desk - Page 44

Power-On / Setup Password, Cable Lock Provision, I/O Interface Security

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

System Support Power-On / Setup Password These systems include a power-on and setup passwords, which may be enabled or disabled (cleared) through a jumper on the system board. The jumper controls a GPIO input to the SB700 that is checked during POST. To clear the Power-On and/or Setup password, use the following procedure: 1. Turn off the system and disconnect the AC power cord from the outlet and/or system unit. 2. Remove the cover (hood) as described in the appropriate User Guide or Maintainance And Service Reference Guide. Insure that all system board LEDs are off (not illuminated). 3. Locate the password clear jumper (header is colored green and labeled E49 on these systems) and move the jumper from pins 1 and 2 and place on (just) pin 2 (for safekeeping). 4. Replace the cover. 5. Re-connect the AC power cord to the AC outlet and/or system unit. 6. Turn on the system. The POST routine will clear and disable the password. 7. To re-enable the password feature, repeat steps 1-6, replacing the jumper on pins 1 and 2 of header E49. The Setup utility may be configured to be always changeable or changeable only by entering a password. Refer to the previous procedure (Power On / Setup Password) for clearing the Setup password. Cable Lock Provision These systems include a chassis cutout (on the rear panel) for the attachment of an optional cable lock mechanism. I/O Interface Security The SATA, serial, parallel, USB, and diskette interfaces may be disabled individually through the Setup utility to guard against unauthorized access to a system. In addition, the ability to write to or boot from a removable media drive (such as the diskette drive) may be enabled through the Setup utility. The disabling of the serial, parallel, and diskette interfaces are a function of the SIO controller. The USB ports are controlled through the SB700. 4-10 www.hp.com Technical Reference Guide

Section	Page
Title	1
Table of Contents	3
Chapter 1 Introduction	7
Introduction	7
1.1 About this Guide	7
1.1.1 Online Viewing	7
1.1.2 Hardcopy	7
1.2 Additional Information Sources	7
1.3 Serial Number	8
1.4 Notational Conventions	8
1.4.1 Special Notices	8
1.4.2 Values	8
1.4.3 Ranges	8
1.5 Common Acronyms and Abbreviations	9
Chapter 2 System Overview	17
System Overview	17
2.1 Introduction	17
2.2 Features	18
2.3 System Architecture	20
2.3.1 AMD Processor Support	22
2.3.2 Chipset	22
2.3.3 Support Components	23
2.3.4 System Memory	23
2.3.5 Mass Storage	24
2.3.6 Serial Interface	24
2.3.7 Universal Serial Bus Interface	24
2.3.8 Network Interface Controller	24
2.3.9 Integrated Graphics Processor	25
2.3.10 Audio Subsystem	26
Chapter 3 Processor/Memory	29
Processor/Memory Subsystem	29
3.1 Introduction	29
3.2 AMD Processors	30
3.2.1 AMD Processor Overview	30
3.2.2 Processor Changing/Upgrading	30
3.3 Memory Subsystem	31
3.3.1 Memory Loading/Upgrading	32
3.3.2 Memory Mapping and Pre-allocation	33
Chapter 4 System Support	35
System Support	35
4.1 Introduction	35
4.2 PCI Bus Overview	35
4.2.1 PCI 2.3 Bus Operation	35
4.2.2 PCI Express Bus Operation	36
4.2.3 Option ROM Mapping	37
4.2.4 PCI Interrupts	37
4.2.5 PCI Power Management Support	37
4.2.6 PCI Connectors	38
4.3 System Resources	40
4.3.1 Interrupts	40
4.3.2 Direct Memory Access	41
4.4 Real-Time Clock and Configuration Memory	42
4.4.1 Clearing CMOS	42
4.4.2 Standard CMOS Locations	43
4.5 System Management	43
4.5.1 Security Functions	43
4.5.2 Power Management	45
4.5.3 System Status	46
4.5.4 Thermal Sensing and Cooling	46
4.6 Register Map and Miscellaneous Functions	47
4.6.1 System I/O Map	47
4.6.2 GPIO Functions	49
Chapter 5 Input-Output Interfaces	51
Input/Output Interfaces	51
5.1 Introduction	51
5.2 SATA Interfaces	52
5.2.1 SATA Connector	52
5.2.2 AHCI/RAID Support	52
5.3 Diskette Drive Interface	54
5.4 Serial Interface	56
5.5 Parallel Interface Support	57
5.5.1 Standard Parallel Port Mode	57
5.5.2 Enhanced Parallel Port Mode	57
5.5.3 Extended Capabilities Port Mode	57
5.5.4 Parallel Interface Connector	58
5.6 Keyboard/Pointing Device Interface	59
5.6.1 Keyboard Interface Operation	59
5.6.2 Pointing Device Interface Operation	60
5.6.3 Keyboard/Pointing Device Interface Connector	60
5.7 Universal Serial Bus Interface	61
5.7.1 USB Connector	61
5.7.2 USB Cable Data	62
5.8 Audio Subsystem	63
5.8.1 HD Audio Controller	64
5.8.2 HD Audio Link Bus	64
5.8.3 Audio Multistreaming	64
5.8.4 Audio Specifications	65
5.9 Network Interface Controller	66
5.9.1 Wake-On-LAN Support	67
5.9.2 Alert Standard Format Support	67
5.9.3 Power Management Support	67
5.9.4 NIC Connector	68
5.9.5 NIC Specifications	68
Chapter 6 Integrated Graphics Processor	69
Integrated Graphics Processor	69
6.1 Introduction	69
6.2 Functional Description	70
6.3 Upgrading	71
6.4 Monitor Connectors	72
6.4.1 Analog Monitor Connector	72
6.4.2 DVI-D Connector	73
Chapter 7 Power and Signal Distribution	75
Power and Signal Distribution	75
7.1 Introduction	75
7.2 Power Distribution	75
7.2.1 SFF Power Supply	76
7.2.2 MT Power Supply	77
7.2.3 Optional Energy Star Compliant PSUs	78
7.3 Power Control	78
7.3.1 Power Button	78
7.3.2 Wake Up Events	80
7.3.3 Power Management	81
7.4 Signal Distribution	82
Chapter 8 BIOS ROM	85
SYSTEM BIOS	85
8.1 Introduction	85
8.2 ROM Flashing	86
8.2.1 Upgrading	86
8.2.2 Changeable Splash Screen	86
8.3 Boot Functions	87
8.3.1 Boot Device Order	87
8.3.2 Network Boot (F12) Support	87
8.3.3 Memory Detection and Configuration	87
8.3.4 Boot Error Codes	88
8.4 Client Management Functions	89
8.4.1 System ID and ROM Type	91
8.6 USB Legacy Support	92
8.7 Management Functions	92
Appendix A Error Messages and Codes	93
A.1 Introduction	93
A.2 Beep/Power LED Codes	93
A.3 Power-On Self Test (POST) Messages	94
A.4 System Error Messages (1xx-xx)	97
A.5 Memory Error Messages (2xx-xx)	98
A.6 Keyboard Error Messages (30x-xx)	99
A.7 Printer Error Messages (4xx-xx)	100
A.8 Video (Graphics) Error Messages (5xx-xx)	100
A.9 Diskette Drive Error Messages (6xx-xx)	101
A.10 Serial Interface Error Messages (11xx-xx)	102
A.11 Modem Communications Error Messages (12xx-xx)	103
A.12 System Status Error Messages (16xx-xx)	104
A.13 Hard Drive Error Messages (17xx-xx)	105
A.14 Hard Drive Error Messages (19xx-xx)	107
A.15 Video (Graphics) Error Messages (24xx-xx)	108
A.16 Audio Error Messages (3206-xx)	108
A.17 DVD/CD-ROM Error Messages (33xx-xx)	109
A.18 Network Interface Error Messages (60xx-xx)	109
A.19 SCSI Interface Error Messages (65xx-xx, 66xx-xx, 67xx-xx)	110
A.20 Pointing Device Interface Error Messages (8601-xx)	111

Match case Limit results 1 per page

4-10

www.hp.com

Technical Reference Guide

System Support

Power-On / Setup Password

These systems include a power-on and setup passwords, which may be enabled or disabled

(cleared) through a jumper on the system board. The jumper controls a GPIO input to the SB700

that is checked during POST.

To clear the Power-On and/or Setup password, use the following procedure:

1. Turn off the system and disconnect the AC power cord from the outlet and/or system unit.

2. Remove the cover (hood) as described in the appropriate User Guide or Maintainance And

Service Reference Guide. Insure that all system board LEDs are off (not illuminated).

Locate the password clear jumper (header is colored green and labeled E49 on these systems)

and move the jumper from pins 1 and 2 and place on (just) pin 2 (for safekeeping).

4. Replace the cover.

5. Re-connect the AC power cord to the AC outlet and/or system unit.

6. Turn on the system. The POST routine will clear and disable the password.

7. To re-enable the password feature, repeat steps 1-6, replacing the jumper on pins 1 and 2 of

header E49.

The Setup utility may be configured to be always changeable or changeable only by entering a

password. Refer to the previous procedure (Power On / Setup Password) for clearing the Setup

password.

Cable Lock Provision

These systems include a chassis cutout (on the rear panel) for the attachment of an optional cable

lock mechanism.

I/O Interface Security

The SATA, serial, parallel, USB, and diskette interfaces may be disabled individually through

the Setup utility to guard against unauthorized access to a system. In addition, the ability to write

to or boot from a removable media drive (such as the diskette drive) may be enabled through the

Setup utility. The disabling of the serial, parallel, and diskette interfaces are a function of the SIO

controller. The USB ports are controlled through the SB700.