Craftsman 11585 Operation Manual - Page 6

ignition, light., location., leakage, liquid, immediately, if liquid, least, immediate, LASER, laser

Get Craftsman 11585 - C3 19.2 Volt 7-1/4 in. Circular Saw PDF manuals and user guides View all Craftsman 11585 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

[] Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possibly injury. [] Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately. [] Batteries can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately. [] Do not charge battery tool in a damp or wet location. Following this rule will reduce the risk of electric shock. [] For best results, your battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F. Do not store outside or in vehicles. [] Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar, if liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk of serious personal injury. [] if the power supply cord is damaged, it must be replaced only by the manufacturer or by an authorized service center to avoid risk. LASER GUIDE WARNINGS: The laser guide radiation used in the Craftsman circular saw is Class Ilia with maximum

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
[]
Do
not place
battery
tools
or their
batteries
near
fire
or heat. This will reduce the risk of explosion
and
possibly
injury.
[]
Do
not crush,
drop
or damage
battery
pack.
Do
not use a battery
pack
or charger
that
has been
dropped
or received
a sharp
blow.
A damaged
battery is subject to explosion.
Properly
dispose
of a
dropped
or damaged
battery immediately.
[]
Batteries
can explode
in the presence
of a source
of
ignition,
such
as a pilot
light.
To reduce the risk of
serious
personal injury, never use any cordless
product
in the presence
of open flame. An exploded
battery
can propel debris
and chemicals.
If exposed,
flush with
water immediately.
[]
Do
not charge
battery
tool
in a damp
or wet
location.
Following this rule will reduce the risk of
electric
shock.
[]
For best
results,
your
battery
tool should
be
charged
in
a location
where
the temperature
is
more
than 50°F but
less
than 100°F.
Do
not store
outside
or
in
vehicles.
[]
Under
extreme
usage
or temperature
condi-
tions,
battery
leakage
may occur.
If
liquid
comes
in
contact
with
your
skin,
wash
immediately
with
soap
and
water,
then
neutralize
with
lemon
juice
or vinegar,
if liquid
gets
into
your
eyes,
flush
them
with
clean
water
for
at
least
10 minutes,
then seek
immediate
medical
attention.
Following
this rule will
reduce the risk of serious personal
injury.
[]
if
the power
supply
cord
is
damaged,
it
must be
replaced only by the manufacturer
or by an authorized
service
center to avoid risk.
LASER
GUIDE
WARNINGS:
The
laser
guide radiation used
in
the Craftsman
circular
saw is Class Ilia with maximum
<5mW and 650nm
wavelengths.
These lasers do not normally
present an
optical
hazard although staring
at the beam may cause
flash blindness.
[]
Avoid direct eye exposure
when using the
laser
guide.
[]
The laser shall be used and maintained
in
accordance
with the manufacturer's
instructions.
[]
[]
Never aim the beam at a person or object
other than
the workpiece.
Always
ensure the laser beam
is
aimed at a sturdy
workpiece
without
reflective surfaces.
Shiny reflective
sheet metal or similar shiny materials
are not suitable
for laser use.
[]
[]
All repairs should be made by an authorized
service
representative
or the
laser
manufacturer.
Save
these
instructions.
Refer to them frequently
and
use them to
instruct
others who may use this tool. If
you
loan
someone
this tool, loan them these
instruc-
tions also to prevent misuse
of the product
and
possible
injury.