Craftsman 28907 Operation Manual - Page 8

Extension

Get Craftsman 28907 - Lt 2000 19.5 HP/42inch Lawn Tractor PDF manuals and user guides View all Craftsman 28907 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

BEFORE REMOVING TRACTOR FROM SKID TO CHECK BATTERY 1. Lift seat to raised position. NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions). • For batteryand batterycabte installation see "REPLACING BATTERY" in the "Service and Adjustments" section in this manual. Label INSTALL STEERING WHEEL 3. Position front wheels of the tractor so they are pointing straight forward. 4. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension. 5. Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter. 6. Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely. 7. Snap steering wheel insert into center of steering wheel. 8. Remove protective materials from tractor hood and grill. IMPORTANT: Check for and remove any staples in skid that may puncture tires where tractor is to roll off skid. INSTALL SEAT 1. Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard. 2. Connect switch to seat. ATTACH STEERING WHEEL ASSEMBLE EXTENSION SHAFT AND BOOT 1. Slide extension shaft onto lower steer- ing shaft. 2. Place tabs of steering boot over tab slots in dash and push down to secure. Insert , :'jHex Bolt _I_'L L°gekFWa_lsher __,J'_Washer /__/_,,, Steering Wheel __;:i'iSteering Boot '::_Tabs S@ T:? Adapter f _'"/ ,,_ .ExtenSsihoanh Tab --_ Seat / _ switch _ f- _"" Slot pan / J Ii Tape Wiring harness 3. Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan. 4. Push down on seat to engage pads in slots and pull seat towards rear of tractor. 5. Raise seat and tighten bolt securely. 6. Remove tape and discard. Slot Tape Flat washer \ pan Bolt Tab 8 Adjustment handle

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
BEFORE
REMOVING
TRACTOR
FROM SKID
TO CHECK
BATTERY
1.
Lift seat to raised position.
NOTE: If this battery is put into service after
month and year indicated
on label (label is
located
between terminals)
charge battery
for minimum of one hour at 6-10 amps. (See
"BATTERY"
in Maintenance
section of this
manual for charging
instructions).
•
For batteryand
batterycabte
installation
see
"REPLACING
BATTERY"
in
the
"Service
and Adjustments"
section
in
this manual.
Label
ATTACH
STEERING
WHEEL
ASSEMBLE
EXTENSION
SHAFT
AND
BOOT
1.
Slide extension shaft onto lower steer-
ing shaft.
2.
Place tabs of steering
boot over tab
slots in dash and push down to secure.
Insert
, :'jHexBolt
_I_'L
L°gekFWl
a_sher
__,J'_Washer
/__/_,,,
Steering
Wheel
__;i
:'iSteering
Boot
'::_Tabs
@:
ST?
.Extension
Shah
Adapter f
_'"/
Tab
,,_
--_
\
INSTALL STEERING
WHEEL
3.
Position front wheels of the tractor so
they are pointing
straight forward.
4.
Remove
steering wheel adapter
from
steering wheel and slide adapter
onto
steering shaft extension.
5.
Position steering
wheel so cross bars
are horizontal
(left to right) and slide
inside boot and onto adapter.
6. Assemble
large flat washer, 5/16 lock
washer, 5/16 hex bolt and tighten
securely.
7.
Snap steering
wheel insert into center
of steering wheel.
8.
Remove
protective
materials from trac-
tor hood and grill.
IMPORTANT:
Check for and remove any
staples
in skid that may puncture
tires
where tractor
is to roll off skid.
INSTALL
SEAT
1.
Remove
bolt and flat washer
securing
seat to cardboard
packing and set aside
for assembly
of seat to tractor.
Remove
the cardboard
packing and discard.
2.
Connect
switch to seat.
Seat
/
_
_ f-
_""
switch
Slot
/
J
pan
I
i
Tape
Wiring
harness
3.
Place seat
on seat pan so all three
(3)
bottom
pads are positioned
over
large
slotted holes in pan.
4.
Push down
on seat to engage
pads in
slots and pull seat towards rear of tractor.
5.
Raise seat and tighten
bolt securely.
6.
Remove
tape and discard.
Slot
Tape
Flat
washer
8
pan
Adjustment
Bolt
Tab
handle