Craftsman CRAFTSMAN Owners Manual - Page 10

Warning, Charging Battery Pack, To Charge - sears tools

Page 10 highlights

• Lock the switch trigger by placing FORWARD/REVERSE SELECTOR in the center position. • Depress latch located on front of battery pack (1) to release battery pack. • Pull forward on battery pack (2) to remove from impact wrench. WARNING: If any parts are missing, do not operate your impact wrench until the missing parts are replaced. Failure to do so could result in possible serious personal injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. CHARGING BATTERY PACK The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until light on front of charger changes from red to green. NOTE:Batteries will not reach full charge the first time they are charged. Allow several cycles (using impact wrench followed by recharging) for them to become fully charged. Figure 6: Battery Charger TO CHARGE • Charge battery pack only with the charger provided. • Make sure power supply is normal house voltage, 120 volts, 60 Hz, AC only. • Connect charger to power supply. • Attach battery pack to charger by aligning raised ribs on battery pack with grooves in charger, then slide battery pack onto charger. • Red light should turn on. Steady red light indicates normal fast charging mode. If red light is flashing, this indicates battery pack is deeply discharged or hot. If battery pack is hot, red light should become steady after battery pack has cooled down. If battery pack is deeply discharged, red light should become steady after voltage has increased, normally within 60 minutes. If after one hour red light is still flashing, this indicates a defective battery pack that should be replaced. Green light ON indicates battery pack is fully charged and slow charging to maintain battery pack. Yellow light ON and red light flashing indicates defective battery pack. Return battery pack to your nearest Sears Repair Center for checking or replacing. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15

10
Lock the switch trigger by placing
FORWARD/REVERSE SELECTOR
in the center position.
Depress latch located on front of
battery pack (1) to release battery
pack.
Pull forward on battery pack (2) to
remove from impact wrench.
WARNING:
If any parts are
missing, do not operate your
impact wrench until the missing
parts are replaced. Failure to do so
could result in possible serious
personal injury.
WARNING:
Always wear safety
goggles or safety glasses with side
shields when operating tools.
Failure to do so could result in
objects being thrown into your
eyes, resulting in possible serious
injury.
CHARGING BATTERY PACK
The battery pack for this tool has been
shipped in a low charge condition to
prevent possible problems. Therefore,
you should charge it until light on front
of charger changes from red to green.
NOTE:
Batteries will not reach full
charge the first time they are charged.
Allow several cycles (using impact
wrench followed by recharging) for
them to become fully charged.
TO CHARGE
Charge battery pack only with the
charger provided.
Make sure power supply is normal
house voltage, 120 volts, 60 Hz,
AC only.
Connect charger to power supply.
Attach battery pack to charger by
aligning raised ribs on battery pack
with grooves in charger, then slide
battery pack onto charger.
Red light should turn on. Steady
red light indicates normal fast
charging mode. If red light is flash-
ing, this indicates battery pack is
deeply discharged or hot.
If battery pack is hot, red light should
become steady after battery pack
has cooled down.
If battery pack is deeply discharged,
red light should become steady after
voltage has increased, normally
within 60 minutes.
If after one hour red light is still flash-
ing, this indicates a defective battery
pack that should be replaced.
Green light ON indicates battery
pack is fully charged and slow charg-
ing to maintain battery pack.
Yellow light ON and red light flashing
indicates defective battery pack.
Return battery pack to your nearest
Sears Repair Center for checking or
replacing.
Figure 6: Battery Charger