Cub Cadet 2X 30 inch MAX Operation Manual - Page 8

Side Mounted Chute Rotation Control w, Manual Pitch, Overhead Chute Rotation Control, w/ Manual

Get Cub Cadet 2X 30 inch MAX PDF manuals and user guides View all Cub Cadet 2X 30 inch MAX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

ASSEMBLY Side Mounted Chute Rotation Control w/ Manual Pitch Chute Assembly Chute Control Rod 3. Remove plastic cap (if present), flat washer (a) and hairpin clip (b) from end of chute control rod (Figure 11). a Figure 8 1. Position chute assembly over base (Figure 9). b Figure 11 4. Insert end of chute control rod into lower bracket and secure with flat washer (a), hairpin clip (b) and plastic cap (if present) removed in Step 1. If necessary, lower bracket can be adjusted. Refer to Side Chute Control on page 16. STOP Continue to Set-Up (page 14). Overhead Chute Rotation Control w/ Manual Pitch Chute Assembly Chute Control Rod Figure 9 2. Close flange keepers to secure chute assembly to chute base. Flange keepers will click into place when properly secured (Figure 10). Figure 10 NOTE: Ensure the lower chute is secured to the flange on the chute base. The lower edge of the chute keeper should be positioned below the flange on the chute base after being clicked into place. If flange keepers will not easily click into place, use palm of your hand to apply swift, firm pressure to the back of the keepers. Figure 12 1. Remove wing nut (a) and hex screw (b) from chute control head and clevis pin (c) and cotter pin (d) from chute support bracket. Position chute assembly (forward-facing) over chute base and chute support bracket (Figure 13). 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
8
ASSEMBLY
Side Mounted Chute Rotation Control w/
Manual Pitch
Chute Assembly
Chute Control Rod
Figure 8
1.
Position chute assembly over base (Figure 9).
Figure 9
2.
Close flange keepers to secure chute assembly to chute base.
Flange keepers will click into place when properly secured
(Figure 10).
Figure 10
NOTE:
Ensure the lower chute is secured to the flange on the
chute base.
The lower edge of the chute keeper should be
positioned below the flange on the chute base after being clicked
into place. If flange keepers will not easily click into place, use
palm of your hand to apply swift, firm pressure to the back of
the keepers.
3.
Remove plastic cap (if present), flat washer (a) and hairpin
clip (b) from end of chute control rod (Figure 11).
a
b
Figure 11
4.
Insert end of chute control rod into lower bracket and
secure with flat washer (a), hairpin clip (b) and plastic cap (if
present) removed in Step 1. If necessary, lower bracket can be
adjusted. Refer to Side Chute Control on page 16.
STOP
Continue to Set-Up (page 14).
Overhead Chute Rotation Control
w/ Manual Pitch
Chute Control Rod
Chute Assembly
Figure 12
1.
Remove wing nut (a) and hex screw (b) from chute control
head and clevis pin (c) and cotter pin (d) from chute support
bracket. Position chute assembly (forward-facing) over chute
base and chute support bracket (Figure 13).