D-Link DCS-3220 Product Manual - Page 6

Connections - support

Get D-Link DCS-3220 - SECURICAM Network Camera PDF manuals and user guides
UPC - 790069269516
View all D-Link DCS-3220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Connections DC Power Connector Audio Out Connector Reset Button I/O Connector Ethernet Cable Connector Ethernet Cable Connector The DCS-3220 back panel features an RJ-45 connector for connections to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling. This network port supports the NWay protocol, allowing the Internet Camera to automatically detect or negotiate the transmission speed of the network. The Ethernet cable included with the DCS-3220 Internet Camera is a Category 5 "straight through" cable. This is the recommended cable type when the camera is connected to a 100 Mbps Fast Ethernet network hub or switch. DC Power Connector The DC power input connector is located on the DCS-3220 Internet Camera's back panel and is labeled DC 12V with a single socket to supply power to the Internet Camera. .Reset Button Reset will be initiated when the reset button is pressed once and held until the Power LED flashes through its cycle twice A reset to factory defaults will be initiated when the reset button is pressed continuously for 5 seconds or when the Power LED changes from green to red for 2 cycles. (For example you will see the LED turn to red twice, release the reset button when the LED turns red the second time). The Power LED will begin to flash indicating that the Internet Camera's settings are reverting back to the factory settings, then turn back to green. To reset the camera, press the reset button once, and the LED will flash to orange. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
6
Connections
Ethernet Cable Connector
The
DCS-3220
back panel features an
RJ-45
connector for connections to
10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling. This network
port supports the
NWay protocol
, allowing the Internet Camera to automatically
detect or negotiate the transmission speed of the network.
.
DC Power Connector
The DC power input connector is located on the
DCS-3220
Internet Camera’s
back panel and is labeled
DC 12V
with a single socket to supply power to the
Internet Camera.
A reset to factory defaults will be initiated when the reset button is pressed
continuously for 5 seconds or when the Power LED changes from
green
to
red
for 2 cycles. (For example you will see the LED turn to
red
twice, release
the reset button when the LED turns red the second time). The Power LED
will begin to flash indicating that the Internet Camera’s settings are reverting
back to the factory settings, then turn back to
green
.
To reset the camera,
press the reset button once, and the LED will flash to
orange
.
The Ethernet cable included with the DCS-3220 Internet Camera is a
Category 5
“straight through” cable.
This is the recommended cable type
when the camera is connected to a 100 Mbps Fast Ethernet network hub or
switch.
Ethernet Cable Connector
DC Power Connector
I/O Connector
Reset Button
Audio Out Connector
Reset Button
Reset will be initiated when the reset button is pressed once and held until the
Power LED flashes through its cycle twice