D-Link DCS-6111 Quick Installation Guide

D-Link DCS-6111 Manual

Get D-Link DCS-6111 PDF manuals and user guides
UPC - 790069318412
View all D-Link DCS-6111 manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DCS-6111 manual content summary:

  • D-Link DCS-6111 | Quick Installation Guide - Page 1
  • D-Link DCS-6111 | Quick Installation Guide - Page 2
    Ring Enclosure WDR D&N FIXED DOME Network Camera Ver. 1.00 DCS-6111 CD-ROM with Manual and Setup Wizard AC Power Adapter CAT5 Ethernet Cable Screwdriver Screws and I/O Connector If any of the above items are missing, please contact your reseller. D-Link DCS-6111 Quick Install Guide 
  • D-Link DCS-6111 | Quick Installation Guide - Page 3
    speed of the network.The Ethernet port can also be used to power the camera by using a PoE switch. Reset Button Press and hold the reset button until the Power LED flashes through its cycle twice. This will reset the camera to its factory default settings.  D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 4
    Hardware Overview Zoom Controller Focus Controller Tilt Screw Adjustment Screw Pan Screw DI / DO LEDs Power/Activity LED D-Link DCS-6111 Quick Install Guide 
  • D-Link DCS-6111 | Quick Installation Guide - Page 5
    stencil are located. Insert the supplied plastic anchors into the drilled holes, and align the holes at the base of the camera with the plastic anchors. Once aligned, insert the provided screws through the holes. Use screwdriver to tighten and secure.  D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 6
    cable and connect the supplied power cable from the camera to a power outlet. Connection with a PoE Switch If using a PoE switch or router, connect the IP camera via Ethernet cable, which will provide both power and data transmission over a single cable. D-Link DCS-6111 Quick Install Guide 
  • D-Link DCS-6111 | Quick Installation Guide - Page 7
    Installation Turn on the computer and insert the D-Link DCS-6111 Autorun CD into the CD-ROM drive. The following step-by-step instructions displayed are shown when using Windows Vista® Click Next Click I Agree to accept the License Agreement. Click I Agree  D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 8
    Software Installation To start the installation click Install. Note: The installation may take several minutes to complete. Click Install Click Finish to complete the installation. Click Finish D-Link DCS-6111 Quick Install Guide 
  • D-Link DCS-6111 | Quick Installation Guide - Page 9
    is a device that supplies the IP address such as a router. Click Manual Setup Enter and confirm a password if you wish to assign one for your admin account. Click Next to continue. Note: The default Admin ID is admin with the password left blank. Click Next  D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 10
    to obtain a new IP address every time the camera starts up. Click Next to continue. Click Next Select UPnP Port Forwarding if your router supports this function. If not, choose Manual to manually enter your port numbers. Click Next to continue. Click Next D-Link DCS-6111 Quick Install Guide 10
  • D-Link DCS-6111 | Quick Installation Guide - Page 11
    asking you if you want to access the DCS-6111 via mobile phone. Clicking Yes will set the video resolution to 176x144. Click Yes Click Apply to apply the settings listed in the window to the device. Application may take a few minutes to process. Click Apply 11 D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 12
    access your device. Click Add to my favorite to save the address and then click Exit to complete the installation. Click Exit Double-click the DCS-6111 to launch the camera's web configuration page. Note: Please see the user manual for more information. D-Link DCS-6111 Quick Install Guide 12
  • D-Link DCS-6111 | Quick Installation Guide - Page 13
    as the default username and leave the password blank. Click OK to continue. This section shows your camera's live video. You may control the settings using the buttons at the bottom. For more information on using the web configuration, please refer to the user manual. 13 D-Link DCS-6111 Quick
  • D-Link DCS-6111 | Quick Installation Guide - Page 14
    once completed. Loosen the image adjustment screw and turn the lens to adjust the IP camera's image until the desired orientation is achieved, tighten the image adjustment screw once completed the image is clear. Tighten the focus controller once completed. D-Link DCS-6111 Quick Install Guide 14
  • D-Link DCS-6111 | Quick Installation Guide - Page 15
    the dome enclosure over the IP camera so that the LED sticker on the dome enclosure is properly aligned with the camera's dome enclosure. When attachment is successfully made, the line on the ring enclosure will be aligned with the line on the dome enclosure. 15 D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 16
    administrator to manage up to 32 D-Link IP cameras remotely. The administrator can use the software to configure the advanced settings for the camera. D-ViewCam is a complete management versions. Select a language version and click OK to continue. Click OK D-Link DCS-6111 Quick Install Guide 16
  • D-Link DCS-6111 | Quick Installation Guide - Page 17
    Next Click Browse if you would like to choose a specific folder for the installation, otherwise click Next to continue. Click Next Click Next to start the installation. Note: The D-ViewCam installation process may take several minutes to complete. Click Next 17 D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 18
    D-ViewCam Installation Click Finish to complete the installation. Click Finish D-Link DCS-6111 Quick Install Guide 18
  • D-Link DCS-6111 | Quick Installation Guide - Page 19
    D-ViewCam, click on Start > All Programs > D-Link > D-Link D-ViewCam. Use admin as the default user name and leave the password blank. Click the to continue. The D-ViewCam screen will appear as shown below. Click (Next) to begin the Add Camera wizard. 19 D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 20
    under the default map called My Map. Click Next to continue. If you choose Add Manually, enter the IP address, Device Port, Model Name, Camera ID and Password. Click the "?" button to auto detect the camera's model name, then the model name will appear in the Model Name box. D-Link DCS-6111 Quick
  • D-Link DCS-6111 | Quick Installation Guide - Page 21
    Click to continue. Adding a Camera D-ViewCam shows the detected IP camera(s) information. You can choose and schedule the recording for each camera(s). • 24/7 Continuous Recording: motion is detected. Please refer to the user manual for more information. 21 D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 22
    D-ViewCam Installation Select Yes to add another camera, or select No to continue. Note: After you have finished adding your camera(s), click Close to view your camera(s). Your D-ViewCam Installation is Complete! D-Link DCS-6111 Quick Install Guide 22
  • D-Link DCS-6111 | Quick Installation Guide - Page 23
    Notes Notes 23 D-Link DCS-6111 Quick Install Guide
  • D-Link DCS-6111 | Quick Installation Guide - Page 24
    . Product specifications, size and shape are subject to change without notice, and actual product appearance may differ from that depicted on the packaging. Visit www.dlink.com for more details. D-Link DCS-6111 Quick Install Guide 24
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24