D-Link DGS-1500-20 User Manual - Page 24

Monitor, IP Address, Protocol version, Product Name, System Name, Location, Trap IP, Subnet Mask

Get D-Link DGS-1500-20 PDF manuals and user guides View all D-Link DGS-1500-20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

4 SmartConsole Utility D-Link Web Smart Switch User Manual Definitions of the Device List features: Monitor: Checking the Monitor box and the SmartConsole will collect the trap and log data from the device. The in the monitor means the device was discovered by SmartConsole. Click the icon to have the device to continue updating the information, such as system log or trap to the SmartConsole Utility. The icon will appear . When the device was detected as not reachable, the icon will change to power or the cable of this device is disconnected. . Please check if the IP Address: Displays the current IP addresses of devices. MAC Address: Displays the device MAC Addresses. Protocol version: Displays the software version of the Utility. Product Name: Displays the device product name. System Name: Displays the appointed device system name. DHCP: Specify if the device gets the IP address from a DHCP server. Location: Displays the location of the appointed device. Trap IP: Displays the IP address of the host where the Trap information will be sent. Subnet Mask: Displays the Subnet Mask setting of the device. Gateway: Displays the Gateway setting of the device. Device Group Interval: Displays the intervals (in seconds) that the Switch will be discovered in the SmartConsole Device List Firmware version: Displays the current Firmware version of this device. LLDP: Displays the LLDP (Link Layer Discovery Protocol) status of the device. SNMP: Displays the SNMP status of the device. NOTE: If the devices are marked red in the device list, it means that a firmware upgrade is required again. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
4
SmartConsole Utility
D-Link Web Smart Switch User Manual
18
Definitions of the Device List features:
Monitor:
Checking the Monitor box and the SmartConsole will collect the trap and log data from the device.
The
in the monitor means the device was discovered by SmartConsole. Click the icon to have the device
to continue updating the information, such as system log or trap to the SmartConsole Utility. The icon will
appear
. When the device was detected as not reachable, the icon will change to
. Please check if the
power or the cable of this device is disconnected.
IP Address:
Displays the current IP addresses of devices.
MAC Address:
Displays the device MAC Addresses.
Protocol version:
Displays the software version of the Utility.
Product Name:
Displays the device product name.
System Name:
Displays the appointed device system name.
DHCP:
Specify if the device gets the IP address from a DHCP server.
Location:
Displays the location of the appointed device.
Trap IP:
Displays the IP address of the host where the Trap information will be sent.
Subnet Mask:
Displays the Subnet Mask setting of the device.
Gateway:
Displays the Gateway setting of the device.
Device Group Interval:
Displays the intervals (in seconds) that the Switch will be discovered in the
SmartConsole Device List
Firmware version:
Displays the current Firmware version of this device.
LLDP
: Displays the LLDP (Link Layer Discovery Protocol
)
status of the device.
SNMP
: Displays the SNMP status of the device.
NOTE:
If the devices are marked red in the device
list, it means that a firmware upgrade is required
again.