D-Link DGS-1500-20 User Manual - Page 54

L2 Functions > LLDP > LLDP Port Settings, Message TX Hold Multiplier 2-10

Get D-Link DGS-1500-20 PDF manuals and user guides View all D-Link DGS-1500-20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

5 Configuration D-Link Web Smart Switch User Manual For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table. Click Apply to make the change effective. Message TX Hold Multiplier (2-10): This parameter is a multiplier that determines the actual TTL value used in an LLDPDU. The default value is 4. Message TX Interval (5-32768): This parameter indicates the interval at which LLDP frames are transmitted on behalf of this LLDP agent. The default value is 30 seconds. LLDP ReInit Delay (1-10): This parameter indicates the amount of delay from the time adminStatus becomes "disabled" until re-initialization is attempted. The default value is 2 seconds. LLDP TX Delay (1-8192): This parameter indicates the delay between successive LLDP frame transmissions initiated by value or status changes in the LLDP local systems MIB. The value for txDelay is set by the following range formula: 1 < txDelay < (0.25 °- msgTxInterval). The default value is 2 seconds. L2 Functions > LLDP > LLDP Port Settings The Basic LLDP Port Settings page displays LLDP port information and contains parameters for configuring LLDP port settings. Figure 5.53 -L2 Functions> LLDP > LLDP Port Settings From Port/ To Port: A consecutive group of ports may be configured starting with the selected port. Notification State: Specifies whether notification is sent when an LLDP topology change occurs on the port. The possible field values are: Enabled - Enables LLDP notification on the port. Disabled - Disables LLDP notification on the port. This is the default value. Admin Status: Specifies the LLDP transmission mode on the port. The possible field values are: TX_Only - Enables transmitting LLDP packets only. RX_Only - Enables receiving LLDP packets only. TX_and_RX - Enables transmitting and receiving LLDP packets. This is the default. Disabled - Disables LLDP on the port. Port Description: Specifies whether the Port Description TLV is enabled on the port. The possible field values are: Enabled - Enables the Port Description TLV on the port. Disabled - Disables the Port Description TLV on the port. System Name: Specifies whether the System Name TLV is enabled on the port. The possible field values are: Enabled - Enables the System Name TLV on the port. Disabled - Disables the System Name TLV on the port. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
5
Configuration
D-Link Web Smart Switch User Manual
48
For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised
from the neighbor in the neighbor table. Click
Apply
to make the change effective.
Message TX Hold Multiplier (2-10):
This parameter is a multiplier that determines the actual TTL value
used in an LLDPDU. The default value is
4
.
Message TX Interval (5-32768):
This parameter indicates the interval at which LLDP frames are transmitted
on behalf of this LLDP agent. The default value is
30
seconds.
LLDP ReInit Delay (1-10):
This parameter indicates the amount of delay from the time adminStatus
becomes "disabled" until re-initialization is attempted. The default value is
2
seconds.
LLDP TX Delay (1-8192):
This parameter indicates the delay between successive LLDP frame
transmissions initiated by value or status changes in the LLDP local systems MIB. The value for txDelay is
set by the following range formula: 1 < txDelay < (0.25 °— msgTxInterval). The default value is
2
seconds.
L2 Functions > LLDP > LLDP Port Settings
The Basic LLDP Port Settings page displays LLDP port information and contains parameters for configuring
LLDP port settings.
Figure 5.53 –L2 Functions> LLDP > LLDP Port Settings
From Port/ To Port:
A consecutive group of ports may be configured starting with the selected port.
Notification State:
Specifies whether notification is sent when an LLDP topology change occurs on the port.
The possible field values are:
Enabled –
Enables LLDP notification on the port.
Disabled –
Disables LLDP notification on the port. This is the default value.
Admin Status:
Specifies the LLDP transmission mode on the port. The possible field values are:
TX_Only –
Enables transmitting LLDP packets only.
RX_Only –
Enables receiving LLDP packets only.
TX_and_RX –
Enables transmitting and receiving LLDP packets. This is the default.
Disabled –
Disables LLDP on the port.
Port Description:
Specifies whether the Port Description TLV is enabled on the port. The possible field
values are:
Enabled –
Enables the Port Description TLV on the port.
Disabled –
Disables the Port Description TLV on the port.
System Name:
Specifies whether the System Name TLV is enabled on the port. The possible field values
are:
Enabled –
Enables the System Name TLV on the port.
Disabled –
Disables the System Name TLV on the port.