D-Link DGS-3224TGR Product Manual - Page 24

IP Addresses and SNMP Community Names, Setting an IP Address, Traps, Cold Start - dgs password

Get D-Link DGS-3224TGR - Switch PDF manuals and user guides
UPC - 790069261244
View all D-Link DGS-3224TGR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

DGS-3224TGR Gigabit Ethernet Switch User's Guide IP Addresses and SNMP Community Names Each switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other TCP/IP application (for example BOOTP, TFTP). The switch's default IP address is 10.90.90.90. You can change the default switch IP Address to meet the specification of your networking address scheme. The switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found when using the command "show switch." In addition, you can also set an IP address for a gateway router. This becomes necessary when the network management station is located on a different IP network from the switch, making it necessary for management packets to go through a router to reach the network manager, and vice-versa. For security, you can set in the switch a list of IP Addresses of the network managers that allow you to manage the switch. You can also change the default SNMP Community Strings in the switch and set the access rights of these Community Strings. In addition, a VLAN may be designated as a Management VLAN. Setting an IP Address The IP address for the switch must be set before it can be managed with the Web-based manager. The switch IP address may be automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to the switch must be known. The IP address may alternatively be set using the Command Line Interface (CLI) over the console serial port as follows: 1. Starting at the command line prompt local>, enter the commands config ipif System ipaddress xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy. Where the x's represent the IP address to be assigned to the IP interface named System and the y's represent the corresponding subnet mask. 2. Alternatively, you can enter the commands config ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x's represent the IP address to be assigned to the IP interface named System and the z represents the corresponding number of subnets in CIDR notation. Using this method, the switch can be assigned an IP address and subnet mask that can then be used to connect a management station to the switch's Web-based management agent. Traps Traps are messages that alert you of events that occur on the switch. The events can be as serious as a reboot (someone accidentally turned OFF the switch), or less serious like a port status change. The switch generates traps and sends them to the network manager (trap recipient). Trap recipients are special users of the network who are given certain rights and access in overseeing the maintenance of the network. Trap recipients will receive traps sent from the switch; they must immediately take certain actions to avoid future failure or breakdown of the network. You can also specify which network managers may receive traps from the switch by entering a list of the IP addresses of authorized network managers. Up to four trap recipient IP addresses, and four corresponding SNMP community strings can be entered. SNMP community strings function like passwords in that the community string entered for a given IP address must be used in the management station software, or a trap will be sent. The following are trap types the switch can send to a trap recipient: • Cold Start -This trap signifies that the switch has been powered up and initialized such that software settings are reconfigured and hardware systems are rebooted. A cold start is different from a factory reset in that configuration settings saved to non-volatile RAM used to reconfigure the switch. • Authentication Failure - This trap signifies that someone has tried to logon to the switch using an invalid SNMP community string. The switch automatically stores the source IP address of the unauthorized user. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
DGS-3224TGR Gigabit Ethernet Switch User’s Guide
12
IP Addresses and SNMP Community Names
Each switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or
other TCP/IP application (for example BOOTP, TFTP). The switch’s default IP address is 10.90.90.90. You can change the
default switch IP Address to meet the specification of your networking address scheme.
The switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found
when using the command “show switch.”
In addition, you can also set an IP address for a gateway router. This becomes necessary when the network management
station is located on a different IP network from the switch, making it necessary for management packets to go through a
router to reach the network manager, and vice-versa.
For security, you can set in the switch a list of IP Addresses of the network managers that allow you to manage the switch.
You can also change the default SNMP Community Strings in the switch and set the access rights of these Community
Strings. In addition, a VLAN may be designated as a Management VLAN.
Setting an IP Address
The IP address for the switch must be set before it can be managed with the Web-based manager. The switch IP address
may be automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to the switch must be
known.
The IP address may alternatively be set using the Command Line Interface (CLI) over the console serial port as follows
:
1.
Starting at the command line prompt
local>
, enter the commands
config ipif System ipaddress
xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy
. Where the
x
’s represent the IP address to be assigned to the IP interface
named
System
and the
y
’s represent the corresponding subnet mask.
2.
Alternatively, you can enter
the commands
config ipif System ipaddress xxx.xxx.xxx.xxx/z
. Where the
x
’s
represent the IP address to be assigned to the IP interface named
System
and the
z
represents the
corresponding number of subnets in CIDR notation.
Using this method, the switch can be assigned an IP address and subnet mask that can then be used to connect a
management station to the switch’s Web-based management agent.
Traps
Traps are messages that alert you of events that occur on the switch. The events can be as serious as a reboot (someone
accidentally turned OFF the switch), or less serious like a port status change. The switch generates traps and sends them to
the network manager (trap recipient).
Trap recipients are special users of the network who are given certain rights and access in overseeing the maintenance of
the network. Trap recipients will receive traps sent from the switch; they must immediately take certain actions to avoid
future failure or breakdown of the network.
You can also specify which network managers may receive traps from the switch by entering a list of the IP addresses of
authorized network managers. Up to four trap recipient IP addresses, and four corresponding SNMP community strings can
be entered.
SNMP community strings function like passwords in that the community string entered for a given IP address must be used
in the management station software, or a trap will be sent.
The following are trap types the switch can send to a trap recipient:
•
Cold Start
–This trap signifies that the switch has been powered up and initialized such that software settings are
reconfigured and hardware systems are rebooted. A cold start is different from a factory reset in that configuration
settings saved to non-volatile RAM used to reconfigure the switch.
•
Authentication Failure
– This trap signifies that someone has tried to logon to the switch using an invalid SNMP
community string. The switch automatically stores the source IP address of the unauthorized user.