D-Link DGS-3420-28PC Hardware Installation Guide - Page 33

Connecting to the Switch for the first time, Connecting to the Management Port

Get D-Link DGS-3420-28PC PDF manuals and user guides View all D-Link DGS-3420-28PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

xStack® DGS-3420 Series Layer 2+ Managed Stackable Gigabit Switch Hardware Installation Reference Guide Connecting to the Switch for the first time The Switch supports user-based security that prevents unauthorized users from accessing the switch or changing its settings. This section explains how to log into the DGS-3420 Series Switch from an out-of-band Management port connection. Once you have connected to the Switch, the following screen appears: UserName: DGS-3420-28SC Gigabit Ethernet Switch Command Line Interface Firmware: Build 1.00.017 Copyright(C) 2011 D-Link Corporation. All rights reserved. Figure 4-2 Initial screen, first time connecting to the Switch Press Enter in both the Username and Password fields. Then access will be given to enter commands after the command prompt DGS-3420-28SC:admin# There is no initial username or password. Leave the Username and Password fields blank. NOTE: The first user automatically gets Administrator level privileges. At least one Admin-level user account must be created for the Switch. Connecting to the Management Port The front panel of the Switch features an out-of-band RJ-45 Management port which can easily connect to a notebook. Connect to the out-of-bound management console using a web browser or Telnet command prompt interface. This is the default login interface, and is the tool you can use when connecting to the Switch for the first time. To use the Management port, connect one end of an Ethernet cable to a computer and the other to the switch. The default IP address of the Management port is 192.168.0.1, and a subnet mask of 255.255.255.0. Make sure that the computer being used for Switch management has a nonconflicting IP address in the 192.168.0.x subnet. The IP settings or enabled status of the Management port can be changed through the console port, or through the web-based Switch management interface. To change the configuration of the Management port, use the command: config out_band_ipif {ipaddress | state [enable | disable] | gateway } To view the status or IP settings, use the command: show out_band_ipif To change settings for the out-of-band Management port in the web interface, use the following path: Management > Out of Band Management Settings 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
xStack® DGS-3420 Series Layer 2+ Managed Stackable Gigabit Switch Hardware Installation Reference Guide
33
Connecting to the Switch for the first time
The Switch supports user-based security that prevents unauthorized users from accessing the switch or changing its
settings. This section explains how to log into the DGS-3420 Series Switch from an out-of-band Management port
connection.
Once you have connected to the Switch, the following screen appears:
DGS-3420-28SC Gigabit Ethernet Switch
Command Line Interface
Firmware: Build 1.00.017
Copyright(C) 2011 D-Link Corporation. All rights reserved.
UserName:
Figure 4–2 Initial screen, first time connecting to the Switch
Press
Enter
in both the Username and Password fields. Then access will be given to enter commands after the
command prompt
DGS-3420-28SC:admin#
There is no initial username or password. Leave the Username and Password fields blank.
NOTE:
The first user automatically gets Administrator level privileges. At least one Admin-level user
account must be created for the Switch.
Connecting to the Management Port
The front panel of the Switch features an out-of-band RJ-45 Management port which can easily connect to a
notebook. Connect to the out-of-bound management console using a web browser or Telnet command prompt
interface. This is the default login interface, and is the tool you can use when connecting to the Switch for the first
time.
To use the Management port, connect one end of an Ethernet cable to a computer and the other to the switch. The
default IP address of the Management port is 192.168.0.1, and a subnet mask of 255.255.255.0. Make sure that the
computer being used for Switch management has a nonconflicting IP address in the 192.168.0.x subnet.
The IP settings or enabled status of the Management port can be changed through the console port, or through the
web-based Switch management interface. To change the configuration of the Management port, use the command:
config out_band_ipif {ipaddress <network_address> | state [enable | disable] | gateway <ipaddr>}
To view the status or IP settings, use the command:
show out_band_ipif
To change settings for the out-of-band Management port in the web interface, use the following path:
Management > Out of Band Management Settings