Dacor DR30G Planning Guides
Dacor DR30G Manual
View all Dacor DR30G manuals
Add to My Manuals
Save this manual to your list of manuals |
Dacor DR30G manual content summary:
- Dacor DR30G | Planning Guides - Page 1
DR30GS, DR30GFS, DR30GIS, DR3GIFS Document # PG05-007 Distinctive™ 30" Wide All Gas Ranges Revised 09/13/12 Page 1/4 PLANNING GUIDE All tolerances ±1/16" (±1.6 mm) unless otherwise noted. 45 9/ This appliance must be installed in accordance with the accompanying installation instructions. Front - Dacor DR30G | Planning Guides - Page 2
DR30GS, DR30GFS, DR30GIS, DR3GIFS Document # PG05-007 Distinctive 30" Wide All Gas Ranges Revised 09/13/12 Page 2/4 PLANNING GUIDE All tolerances +1/16" (+1.6 mm), -0 unless otherwise noted. B 13" (33.0 cm) max.4 Back wall immediately behind range6 Note 1 14" (35.6 cm) A min.4 Note 2 Top - Dacor DR30G | Planning Guides - Page 3
DR30GS, DR30GFS, DR30GIS, DR3GIFS Document # PG05-007 Distinctive 30" Wide All Gas Ranges Revised 09/13/12 Page 3/4 PLANNING GUIDE Self-Rimming Installation Cutout Options (Models DR30GIS and DR30GIFS Only) All tolerances +1/16" (+1.6 mm), -0 unless otherwise noted. For all self-rimming - Dacor DR30G | Planning Guides - Page 4
DR30GS, DR30GFS, DR30GIS, DR3GIFS Document # PG05-007 Distinctive 30" Wide All Gas Ranges Revised 09/13/12 Page 4/4 PLANNING GUIDE 10" (25.4 cm) 10" (25.4 cm) 12" (30.5 cm) 12 1/4" (31.1 cm) to 14 1/4" (36.2 cm) 6' (183 cm) long 2 1/2" (6.4 cm) 3 1/2" (8.9 cm) 1" (2.5 cm) utility clearance
All specifications subject to change without notice.
Phone: (800) 793-0093
www.dacor.com
PLANNING
GUIDE
DR30GS, DR30GFS, DR30GIS, DR3GIFS
Distinctive
™
30” Wide
All Gas Ranges
Document # PG05-007
Revised 09/13/12
Page 1/4
WARNING
•
Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
•
This appliance must be installed in accordance with the
accompanying installation instructions.
All tolerances ±1/16” (±1.6 mm) unless otherwise noted.
OVERALL DEPTH DIMENSIONS - SIDE VIEW
AVAILABLE BACKGUARDS
Part Number
Description
Compatibility
AER30GLBG
Low profile (1 3/4 inch)
Standard on models DR30GIS, DR30GIFS
Optional on models DR30GS, DR30GFS
AERB30G03
3 Inch
Optional on models DR30GS, DR30GFS
NOT compatible with models DR30GIS, DR30GIFS
AERB30G06
6 Inch
Standard on models DR30GS, DR30GFS
NOT compatible with models DR30GIS, DR30GIFS
AERB30G09
9 Inch
Optional on models DR30GS, DR30GFS
NOT compatible with models DR30GIS, DR30GIFS
1 1/8” (2.9 cm)
DR30GI[F]S:
1/4” (6.4 mm)
Front of open door
Front of knobs
Front panel
Rear of front panel
Backguard thickness
26 1/8” (66.4 cm)
28 9/16” (72.5 cm)
24” (61.0 cm)
3” (7.6 cm)
backguard*
DR30G[F]S:
Full stainless
steel side panels
DR30GI[F]S:
(removable)
partial stainless
steel side panels
3 1/4” (8.3 cm)
External handle
shown, some models
have integral handle
1” above trim
Grates extend
backguard*
6” (15.2 cm)
1 3/4” (4.4 cm) backguard*
*�
See table for compatibility
Product width:
29 7/8” (75.9 cm)
NOTE:
Neither version is
compatible with a raised vent.
to
37”
(94.0 cm)
(88.9 cm)
35”
Backguard*
9” (22.9 cm)
45 9/16” (115.7 cm)