Dacor ECS230SCH Installation Instructions - Page 7
electrical, ensure - double wall oven
View all Dacor ECS230SCH manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
Lift the wall oven up to the cabinet cutout, using the upper edge of the cavity opening and the bottom of the oven case side as gripping points. Use extreme caution when lifting the appliance as it is heavy. Be certain to take all necessary safety precautions. Resting the oven on the cabinet-mounting platform, slide the oven into the recessed area until the rear edge of the oven frame is flush with the cabinet face and the oven is centered within the cutout. Ensure that the electrical conduit slides through the opening in the cabinet platform or coils above the oven chassis as the oven is slid into place. The cable must be placed into the recessed area located along the rear vertical edge of the oven or coiled above the oven chassis. Do not trap the appliance cable between the oven case back and the rear wall. / Exhaust Grill Attaching the Exhaust Grill [_ WARNING: Failure to fully rotate the hinge catches will cause them to bend when the door is closed. This will make closing the door impossible. For the single ovens and the upper cavity of the double ovens, locate the mounting holes found in the sides of the oven frame. Using a 1/16" drill, drill four pilot holes for the #6 x 3/4" screws provided in the instruction envelope. Install the screws through the oven frame and into the cabinet to secure the oven. Do not over-tighten the screws. o Secure oven to cabinet with Double Ovens - 6 screws \ \ Installing the Cabinet Mounting Screws Case side bottom both sides Oven Gripping Points Repeat the mounting procedure for the lower cavity if installing a double oven. Installing the Exhaust Grill With the oven now secured to the cabinet, install the Exhaust Grill by mounting it to the oven with the two screws provided. NOTE: You may need to loosen the side mounting screws a little to align the Exhaust Grill mounting holes. Tighten the side mounting screws after attaching the Exhaust Grill. Reinstalling the Oven Doors [_ WARNING: Failure to fully rotate the hinge catches will cause them to bend when the door is closed. This will make closing the door impossible. Grasp the oven door on opposite sides and lift it until the door hinges are aligned with the openings in the oven frame. Holding the door at about a 30 ° angle from the horizontal, slide the hinges into the openings until the bottom hinge arms drop fully into the hinge receptacles. Lower the door to the fully opened position, and then rotate the two hinge catches toward the oven. Open and close the door completely to ensure that it is properly installed. NOTE: You may need to loosen the side mounting screws a little to align the Exhaust Grill mounting holes. Tighten the side mounting screws after attaching the Exhaust Grill. For double ovens, complete Verifying Oven Operation for both the upper and lower doors. For stainless steel ovens, peel off the protective layer of plastic that covers the door panel. Verifying Oven Operation Slide the oven racks onto the support racks within the cavity. Place the broiler pan and tray on a rack within the oven, if desired. Turn on the power supply to the oven. Set the time of day by pressing the Clock touch pad then pressing the TIME.TEMP key. Press the BAKE selector pad for the upper oven or single oven. Select a temperature of 350°F by pressing the TIME.TEMP "+" key. The oven should now be heating. After approximately three (3) minutes, the lower heating element should glow red. Press the CANCEL.SECURE pad to stop the oven heating process. It may take longer than three (3) minutes when ovens are running at voltages lower than 240V. If checking the operation of the double oven, repeat the bake test for the lower oven. Press the BROIL selector pad for the upper oven or single oven. Select a temperature of 350°F by pressing the TIME.TEMP "+" key. The oven should now be heating. After approximately three (3) minutes, the upper heating element should glow red. Press the CANCEL.SECURE pad to stop the oven heating process. It may take longer than three (3) minutes when ovens are running at voltages lower than 240V. If checking the operation of the double oven, repeat the broil test for the lower oven. _} WARNINGS: If the oven does not operate properly, follow these troubleshooting steps: 1. Verify that power is being supplied to the oven. 2. Check the electrical connections to ensure that the installation has been completed correctly. 3. Repeat the above bake test. 4. If the appliance still does not work, contact an authorized DACOR service company at (800) 772-7778. Do not attempt to repair the appliance yourself. DACOR is not responsible for service required to correct a faulty installation. i::}a_*J'_r: 6