Dacor ER30DSR Planning Guides
Dacor ER30DSR Manual
View all Dacor ER30DSR manuals
Add to My Manuals
Save this manual to your list of manuals |
Dacor ER30DSR manual content summary:
- Dacor ER30DSR | Planning Guides - Page 1
Document # PG05-003 ER30D, ER30DSR Epicure® Ranges Revised 02/03/11 Page 1/3 PLANNING GUIDE 46 1/4" (1175 mm) 28 13/16" (732 mm) 27 5/16" information. • This appliance must be installed in accordance with the accompanying installation instructions. 1 9/16" (40 mm) Width at front panel: 29 7/8" - Dacor ER30DSR | Planning Guides - Page 2
Document # PG05-003 ER30D, ER30DSR Epicure® Ranges Revised 02/03/11 Page 2/3 PLANNING GUIDE Product tolerances: ±1/16" (±1.6 mm) unless otherwise stated GAS - by removing the conduit bracket inside the range electrical access box. Gas and Electrical Service ■■ The shaded area (diagram bottom - Dacor ER30DSR | Planning Guides - Page 3
Document # PG05-003 ER30D, ER30DSR Epicure® Ranges Revised 02/03/11 Page 3/3 PLANNING GUIDE Non-combustible rear wall recommeded Cutout tolerances: +1/16", -0, (+1.6 mm, -0) unless otherwise stated panel. Specifications subject to change without notice. www.Dacor.com Phone: (800) 7935-0.9093
PLANNING
GUIDE
Specifications subject to change without notice.
Phone: (800) 793-0093
www.Dacor.com
Epicure
®
Ranges
ER30D, ER30DSR
ELECTRIC CIRCUIT REQUIREMENTS
Range Model
Circuit Required
Total Connected
Load
ER30D/ER30DSR
240 Vac, 4-wire*
60 Hz, 30 Amp.
5.6 kW (24.2 Amp.)
The ratings above are for reference only -
refer to the range rating label
NOTE: Models ER30D and ER30D-C are NOT designed for
use with self-rimming installations or raised vents. Use model
ER30DSR for self-rimming and raised vent installations.
NOTE:
■
Self-rimming models are designed to allow the trim to
overlap the countertop when configured to the dimensions
on page 1/3.
■
Self-rimming models are not compatible with integral
backguards
1 9/16”
(40 mm)
23 1/8” (587 mm)
24 1/8” (613 mm)
27 3/16” (691 mm)
35 3/4”
(908 mm)
to
37 7/8”
(962 mm)
28 11/16” (729 mm)
46 1/8” (1172 mm)
Rear of front panel to
back of chassis
Rear of front panel /oven door
Front panel
Front edge of bullnose
Front of handle
Front of open door
26 3/16” (665 mm)
Width at front panel:
29 7/8” (758 mm)
1 5/16” (33 mm) to cooking
surface (top of grates) from
bottom of trim
SELF RIMMING MODEL ER30DSR
SIDE DIMENSIONS
WITH OPTIONAL RAISED VENT
TRIM KIT INSTALLED (ATK30SR)
1 1/16” (27 mm)
26 5/16” (668 mm)
27 5/16” (694 mm)
28 13/16” (732 mm)
24 1/4” (616 mm)
3” (76 mm)
Backguard*
6” (152 mm)
Backguard**
** Optional
Standard
*
37 7/8”
(962 mm)
to
35 3/4”
(908 mm)
46 1/4” (1175 mm)
Width at front panel:
29 7/8” (758 mm)
Finished side panel
9” (229 mm)
1 9/16”
(40 mm)
Backguard**
1 1/16” (27 mm) to cooking
surface (top of grates) from
top of trim
FREESTANDING MODELS ER30D AND ER30D-C
1 9/16”
(40 mm)
23 1/8” (587 mm)
23 5/8” (600 mm)
26 11/16” (678 mm)
35 3/4”
(908 mm)
to
37 7/8”
(962 mm)
28 3/16” (716 mm)
45 5/8” (1159 mm)
Rear of front panel to
back of chassis
Rear of front panel /oven door
Front panel
Front edge of bullnose
Front of handle
Front of open door
25 11/16” (652 mm)
Width at front panel:
29 7/8” (758 mm)
1 5/16” (33 mm) to cooking
surface (top of grates) from
bottom of trim
SELF RIMMING MODEL ER30DSR
SIDE DIMENSIONS
WITH STANDARD TRIM
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
WARNING
•
Observe all governing codes and ordinances during
planning and installation. Contact your local building
department for further information.
•
This appliance must be installed in accordance with
the accompanying installation instructions.
Document # PG05-003
Revised 02/03/11
Page 1/3
* 4-wire, two 120 Vac hot (L1 and L2), one neutral, one ground