Dacor ER30DSR Planning Guides - Page 1
Dacor ER30DSR Manual
![]() |
View all Dacor ER30DSR manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Document # PG05-003 ER30D, ER30DSR Epicure® Ranges Revised 02/03/11 Page 1/3 PLANNING GUIDE 46 1/4" (1175 mm) 28 13/16" (732 mm) 27 5/16" (694 mm) 26 5/16" (668 mm) 24 1/4" (616 mm) 1 1/16" (27 mm) Product tolerances: ±1/16" (±1.6 mm) unless otherwise stated warning • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • This appliance must be installed in accordance with the accompanying installation instructions. 1 9/16" (40 mm) Width at front panel: 29 7/8" (758 mm) 9" (229 mm) Backguard** 6" (152 mm) 3" (76 mm) Backguard** Backguard* 1 1/16" (27 mm) to cooking surface (top of grates) from top of trim Finished side panel * Standard ** Optional 35 3/4" (908 mm) to 37 7/8" (962 mm) NOTE: ■■ Self-rimming models are designed to allow the trim to overlap the countertop when configured to the dimensions on page 1/3. ■■ Self-rimming models are not compatible with integral backguards 45 5/8" (1159 mm) 28 3/16" (716 mm) 26 11/16" (678 mm) 25 11/16" (652 mm) 23 5/8" (600 mm) 23 1/8" (587 mm) Front of open door Front of handle Front edge of bullnose Front panel Rear of front panel /oven door Rear of front panel to back of chassis FREESTANDING Models ER30D and er30D-C 1 9/16" (40 mm) 1 5/16" (33 mm) to cooking surface (top of grates) from bottom of trim NOTE: Models ER30D and ER30D-C are NOT designed for use with self-rimming installations or raised vents. Use model ER30DSR for self-rimming and raised vent installations. Width at front panel: 29 7/8" (758 mm) 35 3/4" (908 mm) to 37 7/8" (962 mm) 1 9/16" (40 mm) Width at front panel: 29 7/8" (758 mm) 46 1/8" (1172 mm) 28 11/16" (729 mm) 27 3/16" (691 mm) 26 3/16" (665 mm) 24 1/8" (613 mm) 23 1/8" (587 mm) Front of open door Front of handle Front edge of bullnose Front panel Rear of front panel /oven door Rear of front panel to back of chassis Self rimming Model ER30Dsr side dimensions with standard trim 1 5/16" (33 mm) to cooking surface (top of grates) from bottom of trim 35 3/4" (908 mm) to 37 7/8" (962 mm) ELECTRIC CIRCUIT REQUIREMENTS Range Model Circuit Required Total Connected Load ER30D/ER30DSR 240 Vac, 4-wire* 60 Hz, 30 Amp. 5.6 kW (24.2 Amp.) self rimming Model ER30dsr side dimensions with optional RAISED VENT trim kit installed (ATK30SR) * 4-wire, two 120 Vac hot (L1 and L2), one neutral, one ground The ratings above are for reference only refer to the range rating label Specifications subject to change without notice. www.Dacor.com Phone: (800) 7935-0.7093
![](/manual_guide/products/dacor-er30d-planning-guides-f4db062/1.png)