Danby DPAC8399 User Guide - Page 19
Instrucciones para la instalación, del tanque de agua continúa - replacement parts
View all Danby DPAC8399 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
Instrucciones para la instalación del tanque de agua (continúa) 3. Ponga el tanque de agua a la posición correcta sobre la reborde apoyante. Asegúrese de que el conector rápido sobre el tanque de agua está alineado con el conector rápido, instalado a la factoría, localizado al posterior del armario. (véase la figura 37) Fig.39 Fig.37 PRECAUCIÓN Es necesario vaciar el agua acumulada en ambos tanques antes de mover la unidad. 4. Para hacer la coneción, empuje el conector del tanque de agua en el conector del armario. Ud. va a oír un chasquido positivo cuando hace la coneción 5. Instale la tapa sobre el tanque de agua. 6. Para desenganchar (desconectar) el tanque de agua externo, apreta el botón de desenganchar que está en la parte superior del conector rápido del armario, pues sujete los mangos de desenganchar localizado por ambos lados del tanque, levante y tire hacia adelante. (véase la figura 38, 39) Fig.38 Setting the AUTO-ON & AUTO-OFF TIMER Before setting the AUTO-ON & AUTO-OFF Timer, the time of day clock must be set/operational. You must also select the appropriate operating MODE. After the appropriate settings have been made, turn off the unit. 1) Press the TIMER-ON key pad to initiate the AUTO-ON time sequence. (Fig. 32). The display window will indicate TIMER-ON and the word ON will flash for 5 seconds. Press the or key pad to select the desired AUTO-ON start time. (Fig. 32a). key pad will decrease the AUTO-TIMED setting in 10 minute increments. keypad will increase the AUTO-TIMED setting in 10 minute increments. When the desired time is established, (the time will flash in the display window) press the CLOCK key pad to register the AUTO TIMERON program. The word ON will stop flashing and remain "on" (TIMER ON) indicating the program is set. The time of day clock setting will immediately revert back in the display window. The unit must remain "OFF" while programming the AUTO-OFF program. 2) Press the AUTO-OFF key pad to initiate the AUTO-OFF time sequence. (Fig. 33). The display window will indicate TIMER-OFF and the word OFF will flash for 5 seconds. Press the or key pad to select the desired AUTOOFF time. (Fig. 32a). key pad will decrease the AUTO-TIMED setting in 10 minute increments. keypad will increase the AUTO-TIMED setting in 10 minute increments. When the desired time is established, (the time will flash in the display window) press the CLOCK key pad to register the AUTO TIMEROFF program. The word OFF will stop flashing and remain "on" (TIMER OFF) indicating the program is set. The time of day clock setting will immediately revert back in the display window. When the AUTO-ON & AUTO-OFF times are set, within the same program sequence, the display window shows TIMER ON OFF identifying that both ON and OFF times are now programmed (Repeatable daily until until such time the program is canceled and/or changed). IMPORTANT: The desired AUTO-ON & AUTOOFF time must be registered within a 5 second period (after pressing the TIMER-ON/OFF key pads) otherwise the selected time will not register and the system will automatically revert back to the regular "time of day" clock setting The unit will start automatically when the specified AUTO-ON time is achieved on the time of day clock and will stop automatically when the specified AUTO-OFF time is achieved on the time of day clock. To cancel or override the AUTO-TIMED program, simply turn the unit on or off prior to the scheduled AUTO-ON/OFF time. You can verify the AUTO-ON/OFF time selection anytime by pressing each respective TIMER-ON/TIMER-OFF key pad and the selected time will temporarily appear replacing the time of day clock for approximately 5 seconds.