DeLonghi BAR42 Owner Manual - Page 8
Cleaning, Maintenance
View all DeLonghi BAR42 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
6.Re-attach the steam nozzle by inserting it into the steam tube and aligning the 'A' arrow with the 'B' notch, as indicated in figure 22. 7.Re-attach the cappuccino maker by sliding it all the way into the steam nozzle, aligning the 'C' arrow with the 'B' notch, as shown in figure 23, and then turning it in an anti-clockwise direction. PRODUCING HOT WATER 1.Turn on the coffee unit by turning the selector knob to the -W- position (fig. 4). 2.Position a container under the cappuccino maker. 3.When the 'OK' pilot light comes on, position the selector knob at (fig. 7) and at the same time turn the steam kno in an anti-clockwise direction (fig. 19); hot water will come out from the cappuccino maker. 4. To stop the flow of hot water, turn the steam knob in a clockwise direction and position the selector knob at "O" CLEANING AND MAINTENANCE CLEANING THE FILTER HOLDER FOR GROUND COFFEE About every 300 coffees, clean the filter holder for ground coffee as follows: • Remove the filter with the frother; • Clean the inside of the filter holder. Never wash in a dishwasher. • Unscrew the cap of the frother (fig. 24) by rotating in the direction indicated by the arrow on the cap. • Remove the frother from the container by pushing it from the cap end. • Remove the gasket. • Rinse all components and clean the metal filter thoroughly in hot water using a brush (fig. 25). Make sure the holes in the metal filter are not blocked. If necessary, clean with a pin (see fig. 26). • Replace the filter and gasket on the plastic disk as shown in figure 27. Make sure to insert the pin on the plastic disk into the hole in the gasket indicated by the arrow in fig. 27. • Replace the assembly into the steel filter container (fig. 28), making sure the pin is inserted into the hole in the support (see arrow in fig. 28). • Finally, screw on the cap. Failure to clean as described above invalidates the guarantee. CLEANING THE FILTER HOLDER FOR PODS (IF SUPPLIED) About every 300 coffees, clean the filter holder for pods as follows: • Push the filter holder button, remove the filter (fig, 29) and the frother if fitted. Clean the inside of the filter holder. Never wash in a dishwasher. • Remove the gasket from the frother and rinse all components with water. Make sure the holes indicated with the arrows in fig. 30 are not blocked. If necessary, clean with a pin. • Replace the gasket on the frother and replace the assembly in the filter holder. Make sure the tabs of the frother are aligned with the recesses on the filter holder (fig. 31). • Clean the filter thoroughly in hot water using a brush. Make sure the holes in the metal filter are not blocked. If necessary, clean with a pin (see fig. 26). • Replace the filter. Failure to clean as described above invalidates the guarantee. CLEANING THE ESPRESSO BOILER OUTLET At least twice a year, the espresso boiler outlet must be cleaned as follows: • check that the coffee machine is not warm and the plug is detached from the mains; • using a screwdriver, unscrew the screw that holds the outlet of the espresso boiler (fig. 32); • Clean the boiler with a damp cloth (fig. 16); • Clean the outlet thoroughly in hot water using a brush. Make sure the holes are not blocked. IF necessary, clean with a pin. • rinse the outlet under the tap, still scrubbing it; • replace the outlet of the espresso boiler. Failure to clean as described above invalidates the guarantee. OTHER CLEANING OPERATIONS 1.Do not use solvents or detergents in cleaning the: coffee maker. Use a soft, damp cloth. 2.Remove the drip-trays, empty them and wash them periodically ATTENTION: during cleaning, never immerse the unit in water - it is an electrical appliance.