Dell Alienware Area-51 R4 Alienware Area-51 R5 Service Manual - Page 40

Removing the drive-bay heat sensor cable, Prerequisites, Procedure

Get Dell Alienware Area-51 R4 PDF manuals and user guides View all Dell Alienware Area-51 R4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Removing the drive-bay heat sensor cable NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the stability foot. 2. Remove the left and right side-panels. See "Removing the side panels". Procedure 1. Lay the chassis on the right side. Locate the drive-bay heat-sensor connector (SENSOR2) on the system board. For more information on the drive-bay heat-sensor connector, see "system-board components". 2. Disconnect the drive-bay heat-sensor cable from the system board. 3. Turn the chassis over. 4. Remove the cable through the slot on the chassis. Locate the drive-bay heat-sensor. See "right view". 5. Push the release tab and pry the drive-bay heat-sensor cable off the chassis. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
Removing the drive-bay heat sensor cable
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After working
inside your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/
regulatory_compliance
.
Prerequisites
1.
Remove the
stability foot
.
2.
Remove the left and right side-panels. See “
Removing the side panels
”.
Procedure
1.
Lay the chassis on the right side. Locate the drive-bay heat-sensor connector (SENSOR2) on the system board. For more
information on the drive-bay heat-sensor connector, see “
system-board components
”.
2.
Disconnect the drive-bay heat-sensor cable from the system board.
3.
Turn the chassis over.
4.
Remove the cable through the slot on the chassis. Locate the drive-bay heat-sensor. See “
right view
”.
5.
Push the release tab and pry the drive-bay heat-sensor cable off the chassis.
40