Dell DL1000 Appliance Owners Manual - Page 47

Processor, Removing the processor

Get Dell DL1000 PDF manuals and user guides View all Dell DL1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

10. Exit the System Setup. Figure 19. Replacing the system battery 1. system battery 3. battery connector 2. release pin Processor Removing the processor CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Before upgrading your system, download the latest system BIOS version from dell.com/support and follow the instructions included in the compressed download file to install the update on your system. NOTE: You can update the system BIOS using the Lifecycle Controller. 2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. When disconnected from AC power, press and hold the power button for three seconds to fully drain the system of stored power prior to removing the cover. 3. Open the system. 4. Remove the cooling shroud. WARNING: The heat sink and processor are hot to the touch for some time after the system has been powered down. Allow the heat sink and processor to cool before handling them. CAUTION: Never remove the heat sink from a processor unless you intend to remove the processor. The heat sink is necessary to maintain proper thermal conditions. 5. Using the #2 Philips screwdriver, loosen one heat-sink retention screw that secures the heat sink to the system board. 6. Wait 30 seconds for the heat sink to loosen from the processor and remove the screw diagonally opposite the first screw. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
10.
Exit the System Setup.
Figure 19. Replacing the system battery
1.
system battery
2.
release pin
3.
battery connector
Processor
Removing the processor
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
1.
Before upgrading your system, download the latest system BIOS version from
dell.com/support
and
follow the instructions included in the compressed download file to install the update on your
system.
NOTE:
You can update the system BIOS using the Lifecycle Controller.
2.
Turn off the system, including any attached peripherals, and disconnect the system from the
electrical outlet. When disconnected from AC power, press and hold the power button for three
seconds to fully drain the system of stored power prior to removing the cover.
3.
Open the system.
4.
Remove the cooling shroud.
WARNING: The heat sink and processor are hot to the touch for some time after the system
has been powered down. Allow the heat sink and processor to cool before handling them.
CAUTION: Never remove the heat sink from a processor unless you intend to remove the
processor. The heat sink is necessary to maintain proper thermal conditions.
5.
Using the #2 Philips screwdriver, loosen one heat-sink retention screw that secures the heat sink to
the system board.
6.
Wait 30 seconds for the heat sink to loosen from the processor and remove the screw diagonally
opposite the first screw.
47