Dell Inspiron 17 7737 Owners Manual - Page 45

Replacing the System Board, Procedure.

Get Dell Inspiron 17 7737 PDF manuals and user guides View all Dell Inspiron 17 7737 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Replacing the System Board WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in "Before Working Inside Your Computer" on page 7. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 9. For more safety best practices, see the Regulatory Compliance home page at dell.com/regulatory_compliance. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the system setup after you replace the system board. Procedure. 1 Ease the ports on the system board into the slots on the computer base and place the system board in the computer base. 2 Align the screw hole on the system board to the screw hole on the computer base. 3 Replace the screw that secures the system board to the computer base. 4 Connect the camera cable to the system board. 5 Connect the power-adapter port cable to the system board. 6 Connect the hard-drive cable to the hard-disc connector. 7 Connect the speaker cable to the system board. 8 Slide the USB-board cable to the USB-board connector and press down on the latch to secure the cable. 9 Adhere the tape over the USB-board cable. 10 Turn the computer over. 11 Connect the power-button cable to the computer base. 12 Connect the touchpad-board cable to the computer base. 13 Connect the status-light cable to the computer base. Replacing the System Board | 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Replacing the System Board
|
45
Replacing the System Board
WARNING:
Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before Working Inside
Your Computer" on page 7. After working inside your computer, follow the
instructions in "After Working Inside Your Computer" on page 9. For more
safety best practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
NOTE:
Your computer’s Service Tag is stored in the system board. You must enter
the Service Tag in the system setup after you replace the system board.
Procedure.
1
Ease the ports on the system board into the slots on the computer base and place
the system board in the computer base.
2
Align the screw hole on the system board to the screw hole on the computer base.
3
Replace the screw that secures the system board to the computer base.
4
Connect the camera cable to the system board.
5
Connect the power-adapter port cable to the system board.
6
Connect the hard-drive cable to the hard-disc connector.
7
Connect the speaker cable to the system board.
8
Slide the USB-board cable to the USB-board connector and press down on the
latch to secure the cable.
9
Adhere the tape over the USB-board cable.
10
Turn the computer over.
11
Connect the power-button cable to the computer base.
12
Connect the touchpad-board cable to the computer base.
13
Connect the status-light cable to the computer base.