Dell Latitude D630 XFR Service Manual - Page 52

Ground yourself and install the new memory module

Get Dell Latitude D630 XFR PDF manuals and user guides View all Dell Latitude D630 XFR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

DellTM XFR D630 Fully Rugged Notebook Service Manual 1 memory module (DIMM A) 2 securing clips (2) NOTICE: To prevent damage to the memory module connector, do not use tools to spread the memory-module securing clips. 4. If you are replacing a memory module, ground yourself and remove the existing module: a. Use your fingertips to carefully spread apart the securing clips on each end of the memory module connector until the module pops up. b. Remove the module from the connector. 1 securing clips (2) 2 memory module 5. Ground yourself and install the new memory module: a. Align the notch in the module connector with the tab in the connector slot. b. Slide the module firmly into the slot at a 45-degree angle, and rotate the module down until it clicks into place. If you do not feel the click, remove the module and reinstall it. NOTE: If the memory module is not installed properly, the computer may not boot properly. No error message indicates this failure. Page 52 of 106 Revision A01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Dell
TM
XFR D630 Fully Rugged Notebook Service Manual
Page 52 of 106
Revision A01
1
memory module (DIMM A)
2
securing clips (2)
NOTICE:
To prevent damage to the memory module connector, do not use tools to spread the
memory-module securing clips.
4.
If you are replacing a memory module, ground yourself and remove the existing module:
a.
Use your fingertips to carefully spread apart the securing clips on each end of the memory
module connector until the module pops up.
b.
Remove the module from the connector.
1
securing clips (2)
2
memory module
5.
Ground yourself and install the new memory module:
a.
Align the notch in the module connector with the tab in the connector slot.
b.
Slide the module firmly into the slot at a 45-degree angle, and rotate the module down
until it clicks into place. If you do not feel the click, remove the module and reinstall it.
NOTE:
If the memory module is not installed properly, the computer may not boot properly.
No error message indicates this failure.