Dell PowerVault MD3400 Owners Manual - Page 18

Physical Drives, SAFETY Models AMT E03J and E04J, Removing a 2.5 Inch Physical-Drive Blank

Get Dell PowerVault MD3400 PDF manuals and user guides View all Dell PowerVault MD3400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

3. Secure the bezel with the keylock. Physical Drives SAFETY Models AMT E03J and E04J Models AMT, E03J, and E04J are intended for installation only in restricted access locations as defined in cl 1.2.7.3 of IEC 60950-1:2005. Depending on your configuration, your array either supports up to twenty-four 2.5-inch SAS physical drives or up to twelve 3.5-inch SAS physical drives in internal drive bays. Physical drives are connected to a backplane through physical-drive carriers and can be configured as hot-swappable. Removing a 2.5 Inch Physical-Drive Blank CAUTION: To maintain proper system cooling, all empty physical-drive slots must have physicaldrive blanks installed. 1. If installed, remove the front bezel. 2. Press the release button and slide the physical-drive blank out until it is free of the physical-drive slot. Figure 9. Removing and Installing a 2.5 Inch Physical-Drive Blank (MD3420 only) 1. physical-drive blank 2. release button Installing a 2.5 Inch Physical-Drive Blank 1. If installed, remove the front bezel. 2. Insert the physical-drive blank into the physical-drive slot until the release button clicks into place. 3. If applicable, install the front bezel. Removing a 3.5 Inch Physical-Drive Blank CAUTION: To maintain proper system cooling, all empty hard-drive slots must have drive blanks installed. 1. If installed, remove the front bezel. 2. Press the release button and slide the physical-drive blank out until it is free from the physical-drive slot. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
3.
Secure the bezel with the keylock.
Physical Drives
SAFETY Models AMT E03J and E04J
Models AMT, E03J, and E04J are intended for installation only in restricted access locations as defined in
cl 1.2.7.3 of IEC 60950-1:2005.
Depending on your configuration, your array either supports up to twenty-four 2.5-inch SAS physical
drives or up to twelve 3.5-inch SAS physical drives in internal drive bays. Physical drives are connected to
a backplane through physical-drive carriers and can be configured as hot-swappable.
Removing a 2.5 Inch Physical-Drive Blank
CAUTION: To maintain proper system cooling, all empty physical-drive slots must have physical-
drive blanks installed.
1.
If installed, remove the front bezel.
2.
Press the release button and slide the physical-drive blank out until it is free of the physical-drive slot.
Figure 9. Removing and Installing a 2.5 Inch Physical-Drive Blank (MD3420 only)
1.
physical-drive blank
2.
release button
Installing a 2.5 Inch Physical-Drive Blank
1.
If installed, remove the front bezel.
2.
Insert the physical-drive blank into the physical-drive slot until the release button clicks into place.
3.
If applicable, install the front bezel.
Removing a 3.5 Inch Physical-Drive Blank
CAUTION: To maintain proper system cooling, all empty hard-drive slots must have drive blanks
installed.
1.
If installed, remove the front bezel.
2.
Press the release button and slide the physical-drive blank out until it is free from the physical-drive
slot.
18