Dell S4112F Open Networking Hardware Diagnostic Guide December 2021 - Page 50
CPU traffic with external loopback for uplink ports SFP, IXIA traffic with external loopback
View all Dell S4112F manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 50 highlights
Test link_status_test for NPU 0 SKIPPED
Test link_status_test for NPU 0
.............
SKIPPED <<<---
Test snake_traffic_test for NPU 0
.............
Passed
Test prbs_mac_test for NPU 0
.............
SKIPPED <<<---
Test prbs_ext_test for NPU 0
.............
SKIPPED <<<---
Test uplink_link_status_test for NPU 0
.............
SKIPPED <<<---
Test uplink_snake_traffic_test for NPU 0
.............
SKIPPED <<<---
Test uplink_prbs_mac_test for NPU 0
.............
SKIPPED <<<---
Test uplink_prbs_ext_test for NPU 0
.............
SKIPPED <<<---
NPU tests
...........................................
Passed
root@dell-diag-os:~#
IXIA traffic with external loopback
Tests the traffic sent from IXIA to port-1 and to the front-end ports which are connected with external Loopback optics.
Connect the first port to IXIA and all other ports with QSFP28 Loopback optics.
●
nputool -i -t 1 -T ixia_self -d
●
nputool --init --test 1 --traffic ixia_self -d
These commands configure the virtual local area network (VLAN) and after the
BCM.0>
shell displays, send the traffic from
IXIA. To verify the counters, run the
show c
command in the BCM shell. For the S5148F-ON switch, to verify the counters, run
the
show c
command in the XP Shell.
IXIA traffic with adjacent loopback
Tests the traffic sent from IXIA to the front-end ports which are connected with DACs or optics with cables connected
top-to-bottom.
Connect the first two ports to IXIA and all the remaining ports with DACs or 40G/100G optics with cables.
●
nputool –i –t 1 –T ixia_adj
●
nputool --init --test 1 --traffic ixia_adj
The previous commands configure the VLAN and after the
BCM.0>
shell displays. To verify the counters, run the
show c
command in the BCM shell. For the S5148F-ON switch, to verify the counters, run the
show c
command in the XP Shell.
CPU traffic with external loopback for uplink ports (SFP+)
Traffic is sent from the CPU to the SFP+ ports.
Connect all the ports with the SFP+ optics with TX and RX shorted.
●
nputool -i -t 5 -T cpu_self
●
nputool --init --test 5 --traffic cpu_self
CPU traffic for uplink ports connected between adjacent ports
Traffic is sent from the CPU internally generated packet to the front-end Dell EMC SFP+ ports which are connected with SFP+
optics using a cable.
Connect the SFP+ ports with the Dell EMC SFP+ optics using cables.
●
nputool -i -t 5 -T cpu_adj
●
nputool --i --test 5 --traffic cpu_adj
IXIA traffic with external loopback
Traffic is sent from the CPU internally generated packet to the front-end SFP+ ports which are connected with the Dell EMC
SFP+ optics using a cable.
Connect the first port to IXIA and all other ports with Loopback optics.
●
nputool -i -t 5 -T ixia_self -d
●
nputool --init --test 5 --traffic ixia_self -d
Configure the VLAN and display the
BCM.0>
shell. To verify the counters, use the
show c
command in the BCM shell. For the
S5148F-ON switch, to verify the counters, run the
show c
command in the XP Shell.
IXIA traffic with adjacent ports connected to IXIA
Traffic is sent from the CPU internally generated packet to the front-end ports which are connected with DACs or optics using
cables connected top-to-bottom.
Connect two ports to IXIA with SFP+ optics and cables.
50
Dell EMC DAIG-OS tools