Dell S5148F-ON Open Networking Hardware Diagnostic Guide December 2021 - Page 62

D3COLD WakeUp capability advertisement

Get Dell S5148F-ON PDF manuals and user guides View all Dell S5148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

phytool -w -o -V Dump the eeprom contents:= phytool --eeprom-dump (or) phytool -x Dump the register contents:= phytool --reg-dump (or) phytool -d Phy loopback test:= phytool --lb-test[=no of packets] (or) phytool -l[=no of packets] Execute repeatedly command by count:= phytool --iteration=max/ [option1] [option2]... (or) phytool -I max/ [option1] [option2]... Set the interface with parameters:= phytool --set-intf --speed= --duplex= --autoneg (or) phytool -s -S -D -A Show the interface settings:= phytool --show-intf (or) phytool -a Usage:= -h, --h Show the help text -I, --iteration= Iteration command execution -R, --read-mac Read the MAC of the interface -w, --write Write operation -o, --offset Set the Offset -V, --val Value to be set -x, --eeprom-dump Dump the eeprom contents -d, --reg-dump Dump the register contents -l, --lb-test= Phy loopback test -s, --set-intf Set the interface with parameters -S, --speed= Speed -D, --duplex= Duplex mode -A, --autoneg= Auto-negotiation -a, --show-intf Show the interface settings Output root@dellemc-diag-os:/etc/dn/diag# phytool --read-mac 34:17:eb:07:7c:00 root@dellemc-diag-os:/etc/dn/diag# phytool --eeprom-dump Offset Values ------ ------ 0x0000: 34 17 eb 07 7c 00 00 08 ff ff 05 10 ff ff ff ff 0x0010: 18 00 00 00 2f 40 41 1f 86 80 41 1f 86 80 80 ba 0x0020: ff ff ff ff 80 5c 47 00 00 00 40 00 00 4c ab 03 0x0030: 00 00 00 70 0e 1a 26 44 a3 07 42 1f 01 02 02 06 0x0040: 0c 00 47 21 00 00 ff ff ac 44 f6 00 44 1f 08 09 0x0050: 40 04 3c 00 00 00 04 14 00 00 00 00 00 10 ff ff 0x0060: 00 01 00 40 32 13 13 40 00 01 00 40 ff ff b0 03 0x0070: 00 01 00 40 00 01 00 40 d9 09 bc 03 ff ff b5 7e 0x0080: ff ff ff ff a5 0b 00 80 ff ff ff ff ff ff ff ff ..... root@dellemc-diag-os:/etc/dn/diag# phytool --reg-dump 0x00000: CTRL (Device control register) Invert Loss-Of-Signal: Receive flow control: Transmit flow control: VLAN mode: Set link up: D3COLD WakeUp capability advertisement: Auto speed detect: Speed select: Force speed: Force duplex: 0x00008: STATUS (Device status register) Duplex: Link up: Transmission: 0x08100241 no enabled disabled disabled 1 enabled disabled 1000Mb/s no no 0x00282383 full link config on 62 Dell EMC DAIG-OS tools

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
phytool -w -o <offset> -V <val>
Dump the eeprom contents:=
phytool --eeprom-dump
(or)
phytool -x
Dump the register contents:=
phytool --reg-dump
(or)
phytool -d
Phy loopback test:=
phytool --lb-test[=no of packets]
(or)
phytool -l[=no of packets]
Execute repeatedly command by count:=
phytool --iteration=max/<count> [option1] [option2]...
(or)
phytool -I max/<count> [option1] [option2]...
Set the interface with parameters:=
phytool --set-intf --speed=<speed> --duplex=<mode> --autoneg (or)
phytool -s -S <speed> -D <mode> -A
Show the interface settings:=
phytool --show-intf
(or)
phytool -a
Usage:=
-h, --h
Show the help text
-I, --iteration=
Iteration command execution
-R, --read-mac
Read the MAC of the interface
-w, --write
Write operation
-o, --offset
Set the Offset
-V, --val
Value to be set
-x, --eeprom-dump
Dump the eeprom contents
-d, --reg-dump
Dump the register contents
-l, --lb-test=
Phy loopback test
-s, --set-intf
Set the interface with parameters
-S, --speed=
Speed
-D, --duplex=
Duplex mode
-A, --autoneg=
Auto-negotiation
-a, --show-intf
Show the interface settings
Output
root@dellemc-diag-os:/etc/dn/diag# phytool --read-mac
34:17:eb:07:7c:00
root@dellemc-diag-os:/etc/dn/diag# phytool --eeprom-dump
Offset
Values
------
------
0x0000:
34 17 eb 07 7c 00 00 08 ff ff 05 10 ff ff ff ff
0x0010:
18 00 00 00 2f 40 41 1f 86 80 41 1f 86 80 80 ba
0x0020:
ff ff ff ff 80 5c 47 00 00 00 40 00 00 4c ab 03
0x0030:
00 00 00 70 0e 1a 26 44 a3 07 42 1f 01 02 02 06
0x0040:
0c 00 47 21 00 00 ff ff ac 44 f6 00 44 1f 08 09
0x0050:
40 04 3c 00 00 00 04 14 00 00 00 00 00 10 ff ff
0x0060:
00 01 00 40 32 13 13 40 00 01 00 40 ff ff b0 03
0x0070:
00 01 00 40 00 01 00 40 d9 09 bc 03 ff ff b5 7e
0x0080:
ff ff ff ff a5 0b 00 80 ff ff ff ff ff ff ff ff
.....
root@dellemc-diag-os:/etc/dn/diag# phytool --reg-dump
0x00000: CTRL (Device control register)
0x08100241
Invert Loss-Of-Signal:
no
Receive flow control:
enabled
Transmit flow control:
disabled
VLAN mode:
disabled
Set link up:
1
D3COLD WakeUp capability advertisement:
enabled
Auto speed detect:
disabled
Speed select:
1000Mb/s
Force speed:
no
Force duplex:
no
0x00008: STATUS (Device status register)
0x00282383
Duplex:
full
Link up:
link config
Transmission:
on
62
Dell EMC DAIG-OS tools