Dell W-Series 205H W-IAP205H Access Point Installation Guide - Page 1
Dell W-Series 205H Manual
![]() |
View all Dell W-Series 205H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Dell Networking W-IAP205H Instant Access Point Installation Guide The Dell Networking W-IAP205H Instant access point is a high-performance dualradio wired and wireless Instant access point for hospitality and branch deployments. This device combines high-performance wireless mobility with Gigabit wired local access to deliver secure network access to dormitories, hotel rooms, classrooms, medical clinics, and multi-tenant environments. MIMO (Multiple-Input, MultipleOutput) technology enables the W-IAP205H access point to provide wireless 2.4 GHz 802.11n and 5 GHz 802.11 n/ac functionality, while simultaneously supporting existing 802.11a/b/g wireless services. The W-IAP205H access point can be attached to a wall box using the mounting bracket provided, or converted into a desk-mounted remote access point for branch office deployments using the AP-205H-MNTR desk mount kit (sold separately). The W-IAP205H access point works in conjunction with a built-in virtual controller and provides the following capabilities: Dual wireless transceivers IEEE 802.11a/b/g/n/ac operation as a wireless access point IEEE 802.11a/b/g/n/ac operation as a wireless air monitor, spectrum analyzer Supports PoE-in on E0 port (only), and PoE-out on E3 port (only) Compatibility with IEEE 802.3af/at PoE Support for selected USB peripherals NOTE: The W-IAP205H access point requires Dell Instant 4.2 or later. Package Contents W-IAP205H Access Point Single Gang Wall-box Mounting Bracket 2x #6-32 Machine Screw T8H Torx Security Screw Instant Quick Start Guide Regulatory Compliance and Safety Information Guide Installation Guide (this document) NOTE: Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Hardware Overview Figure 1 Front View LED The W-IAP205H access point is equipped with two LEDs indicating System Status and Power Sourcing Equipment (PSE). LED System Status PSE Color/State Meaning Off AP powered off, or LED switched to 'off mode' Amber- Solid AP ready, restricted mode: 10/100Mbps uplink negotiated Either radio in non-HT mode Virtual AP not enabled Amber- Flashing AP in Air Monitor or Spectrum Analyzer mode Red Error condition Green - Flashing AP booting, not ready Green - Solid AP ready Off AP powered off, or PoE capability disabled Green - Solid PoE power enabled Red PoE power sourcing error or overload condition Console Port The W-IAP205H access point is equipped with a serial console port at the back(Figure 2). The port allows connecting the AP to a serial terminal or a laptop for direct local management. The 4-pin connector with removable dust cover is located on the back of the access point. An optional serial adapter cable (AP-CBL-SER) compatible with the W-IAP205H access point can be purchased separately. CAUTION: The back panel of this device may become hot after extended use. ATTENTION: Le panneau arrière du point d'accès AP peut chauffer après une utilisation prolongée. Figure 2 Back View NOTE: Hot-plug operation is not recommended for the console port. Ethernet Ports The W-IAP205H access point is equipped with a total of four active Ethernet ports (E0-E3). The E0 port, located at the bac k of the AP Figure 2 is 10/100/1000 Base-T (RJ-45) auto-sensing, MDI/MDX wired-network uplink connectivity port. It supports IEEE 802.3af/802.3at Power over Ethernet (PoE), accepting 48VDC (nomial) as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE), such as a midspan injector or network infrastructure that supports PoE. The E1-E3 ports, located at the bottom of the AP (Figure 3), are 10/100/1000 Base-T (RJ-45) auto-sensing, MDI/MDX wired-network downlink connectivity ports. They are used to provide secure network connectivity to wired devices. Only the E3 port supports PoE-out functionality, supplying a maximum power of 10W when the AP is operating in 802.3at PoE mode. Additionally, the W-IAP205H access point has a Pass-Through (PT) port at the back (Figure 2) and an E0/PT port at the bottom (Figure 3). The E0/PT port acts primarily as a Pass-Through (PT) port. Alternatively, the E0/PT port can serve as an E0 uplink port and accepts 802.3af/802.3at PoE power when the E0 and PT ports at the back of the AP are physically bridged by an Ethernet cable (AP-CBL-ETH10 sold separately with the AP-205H-MNTR desk mount kit). Figure 3 Bottom View Figure 4 Gigabit Ethernet Port Pin-Out USB Port The W-IAP205H access point is equipped with a USB port that is compatible with cellular modems and Bluetooth Low Energy (BLE) dongles. When the access point is powered by a DC or 802.3at source, the USB port is enabled allowing an output of up to 5W. Push Button The push button located on the side of the W-IAP205H access point can be used to reset the AP to factory default settings or turn off/on the LED display. To reset the AP to factory default settings: 1. Power off the AP. 2. Press and hold the push button using a small, narrow object, such as a paperclip. 3. Power-on the AP without releasing the push button. The system status LED will flash within 5 seconds. 4. Release the push button. The system status LED will flash again within 15 seconds indicating that the reset is completed. The AP will now continue to boot with the factory default settings. To turn off/on the system status LED: During the normal operation of the AP, press the push button using a small, narrow object, such as a paperclip. The system status LED will be turned off/on immediately. Power The W-IAP205H access point has a single 48VDC power connector to support powering through an AC-to-DC power adapter. AP-AC-48V36 adapter (sold separately). The W-IAP205H access point supports both PoE-in and PoE-out functionality. The PoE-in (PoE-PD) allows the E0 port to draw power from an 802.3at (preferred) or 802.3af (optional) sources. Additionally, the PoE-out (PoE-PSE) functionality is enabled on the port 3, allowing a maximum output of 10W. If a device attempts to exceed the 10W power limit, the E3 port is temporarily disabled. The port will automatically reactivates after being disabled. When powered by an 802.3at source, the W-IAP205H access point is able to supply power to PoE-PSE or USB, but not both simultaneously. The default setting for this device is PoE-PSE off, USB on. This setting can be configured in Dell Instant. When powered by an 802.3af source, power sourcing for PoE-PSE and USB is disabled. Power Source DC (AP-AC-48V36) 802.3at 802.3af Restrictions None (USB and PoE-PSE enabled) USB or PoE-PSE enabled USB and PoE-PSE disabled USB PoE-PSE 5W 15.4W 5W 10W N/A N/A NOTE: If both PoE and DC power are available, the AP will default to using DC power. Before You Begin CAUTION: FCC Statement: Improper termination of access points installed in the United States (non-US Regulatory Domain model) will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). ATTENTION: Déclaration FCC: l'arrêt incorrect des points d'accès installés aux États-unis qui sont configurés sur des contrôleurs autres que le modèle agréé aux États-unis est considéré comme contrevenant à l'homologation fcc. toute violation délibérée ou intentionnelle de cette condition peut entraîner une injonction d'arrêt immédiat de son utilisation par la fcc et peut déboucher sur la confiscation de l'équipement (47 cfr 1.80). CAUTION: EU Statement: Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the Dell Networking W-Series Instant User Guide for details on restrictions. Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au Dell Networking W-Series Instant User Guide pour les details des restrictions. Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im Dell Networking WSeries Instant User Guide. Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla Dell Networking W-Series Instant User Guide per avere informazioni detagliate sulle restrizioni. Pre-Installation Network Requirements Pre-Installation Checklist Before installing your W-IAP205H access point, be sure that you have the following: Cat5E UTP cable with network access installed in the wall box One of the following power sources: IEEE 802.3af-compliant Power over Ethernet (PoE) source Dell AP AC-to-DC adapter kit (sold separately) Summary of the Setup Process Complete each of tasks below in the order listed to setup your W-IAP205H access point. 1. Identify the specific installation location for each AP. 2. Install each AP. 3. Verify post-installation connectivity. 4. Configure the virtual controller. Refer to the Dell Networking W-Series Instant Quick Start Guide. NOTE: Dell, in compliance with governmental requirements, has designed the W-IAP205H access point so that only authorized network administrators can change the settings. For more information about AP configuration, refer to the Dell Networking W-Series Instant Quick Start Guide and Dell Networking Instant User Guide. CAUTION: Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used. ATTENTION: Les points d'accès sont des périphériques de transmission radio et sont, en tant que tels, soumis aux réglementations nationales. Les administrateurs réseau responsables de la configuration et de l'exploitation des points d'accès doivent se conformer aux règlements locaux de diffusion. De façon plus précise, les points d'accès doivent employer des canaux adaptés à leur emplacement physique
![](/manual_guide/products/dell-wseries-205h-wiap205h-access-point-installation-guide-e3cd738/1.png)