Denon AVR-1082 Owners Manual - Page 12

ENGLISH NOTES: - Assignment of low frequency signal range - • The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency signal range of channels set to "Small" in the setup menu. The low frequency signal range of channels set to "Large" are produced from those channels. - Crossover Frequency - • When "Subwoofer" is set to "Yes" at the "Speaker Configuration Setting", set the frequency (Hz) below which the bass sound of the various speakers is to be output from the subwoofer (the crossover frequency). • For speakers set to "Small", sound with a frequency below the crossover frequency is cut, and the cut bass sound is output from the subwoofer instead. NOTE: For ordinary speaker systems, we recommend setting the crossover frequency to 80 Hz. When using small speakers, however, setting the crossover frequency to a high frequency may improve frequency response for frequencies near the crossover frequency. - Subwoofer mode - • The subwoofer mode setting is only valid when "Large" is set for the front speakers and "Yes" is set for the subwoofer in the "Speaker Configuration" settings (see page 10). • When the "LFE+MAIN" playback mode is selected, the low frequency signal range of channels set to "Large" are produced simultaneously from those channels and the subwoofer channel. In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency range. • Selection of the "LFE " play mode will play the low frequency signal range of the channel selected with "Large" from that channel only. Therefore, the low frequency signal range that are played from the subwoofer channel are only the low frequency signal range of LFE (only during Dolby Digital or DTS signal playback) and the channel specified as "Small" in the setup menu. • Select the play mode that provides bass reproduction with body. • When the subwoofer is set to "Yes", bass sound is output from the subwoofer regardless of the subwoofer mode setting in surround modes other than Dolby/DTS. Setting the SB CH Auto Flag Detect Set the operation for the digital signals when playing in the 6.1 SURROUND and DTS-ES surround modes. 1 TUNING BAND MODE TUNING ENTER SHIFT At the System Setup Menu select "SB CH Auto Flag Deterct" and press the ENTER button. w Non-Flag Source SBch Output MTRX ON: Sources are played using the surround back speaker(s). The surround back channel is played with digital matrix processing. NON-MTRX: Sources are played using the surround back speaker(s). The same signals as those of the surround channel are output from the surround back speaker(s). OFF: Sources are played without using the surround back speaker(s). 3 ENTER SHIFT Enter the setting. The System Setup Menu reappears. NOTES: • The "SB CH Auto Flag Detect" setting screen is displayed when the surround back speaker is set to "Large" or "Small" at "Speaker Configuration". • The surround back speakers can also be turned on and off using the "6.1/7.1 Surround" surround parameter. (See page 29.) Setting the delay time • Input the distance between the listening position and the different speakers to set the delay time for the surround mode. • The delay time can be set separately for surround speakers A and B. Preparations: Measure the distances between the listening position and the speakers (L1 to L5 on the diagram at the right). L1: Distance between center speaker and listening position L2: Distance between front speakers and listening position L3: Distance between surround speakers and listening position L4: Distance between surround back speakers and listening position L5: Distance between subwoofer and listening position FL Center FR Subwoofer L1 L2 L5 Listening position SL L3 SBL L4 SR SBR 1 At the System Setup Menu select "Delay Time". TUNING BAND MODE TUNING 2 TUNING Select the desired setting. 2 ENTER SHIFT We recommend setting this BAND MODE to "OFF". TUNING When set to "ON", the operation for software for which no identification signals are recorded is set. Setting 3 TUNING q Auto Flag Detect Mode (AFDM) ON: This function only works for sources containing DTS-ES or 6.1-channel surround identification signals. BAND MODE When this function is used, sources that have been recorded in 6.1-channel surround or DTS-ES are TUNING automatically played in the 6.1-channel surround mode using the surround back speaker(s). (Refer to w for the method of playback of the surround back speaker in this case.) OFF: Set this mode if you wish to play normal 5.1-channel sources or sources not containing the identification signals described below in the 6.1-channel mode. Switch to the Delay Time screen. Select the desired unit, meters or feet. Select (darken) the desired units, "Meters" or "Feet". Example: When "Meters" is selected 12