Denon AVR-1082 Owners Manual - Page 24
After starting playback, Playback using the external input EXT. IN jacks
View all Denon AVR-1082 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 24 highlights
ENGLISH Playback using the external input (EXT. IN) jacks 1 Set the external input (EXT. IN) mode. Press the EXT. IN to switch the external input. B EXT.IN EXT.IN (Main unit) (Remote control unit) Once this is selected, the input signals connected to the FL (front left), FR (front right), C (center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right) channels of the EXT. IN jacks are output directly to the front (left and right), center, surround (left and right) and surround back (left and right) speaker systems as well as the pre-out jacks without passing through the surround circuitry. In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SUBWOOFER jack. 2 Cancelling the external input mode To cancel the external input (EXT. IN) setting, press the input mode (AUTO, PCM, DTS) or ANALOG button to switch to the desired input mode. (See page 23.) AUTO PCM DTS ANALOG MODE ANALOG 21 2 6.1 / 7.1 SURROUND DIRECT STEREO MODE INPUT ANALOG EXT.IN SYSTEM CALL CALL 1 CALL 2 BACKLIGHT 1 NOTES: • In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be output from channels not connected to the input jacks. • The external input mode can be set for any input source. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode. (Main unit) (Remote control unit) • When the input mode is set to the external input (EXT. IN), the play mode (DIRECT, STEREO, DOLBY/DTS SURROUND, 5/7CH STEREO, WIDE SCREEN or DSP SIMULATION) cannot be set. After starting playback [1] Adjusting the sound quality (TONE) The tone control function will not work in the Direct mode. 1 The tone switches as follows each time the TONE CONTROL button is pressed. B TONE CONTROL BASS TREBLE (Main unit) 2 With the name of the volume to be adjusted selected, turn the SELECT SELECT knob to adjust the level. 3 21 (Main unit) 3 • To increase the bass or treble: Turn the control clockwise. (The bass or treble sound can be If you do not want the bass and treble to be adjusted, turn on the tone defeat mode. increased to up to +12 dB in steps of 2 dB.) • To decrease the bass or treble: Turn the control clockwise. (The bass or treble sound TONE DEFEAT The signals do not pass through the bass and treble adjustment circuits, providing can be decreased to up to -12 dB in steps of higher quality sound. 2 dB.) (Main unit) [2] Listening over headphones 1 Connect the headphones to the PHONES jack of the front PHONES B panel. 1 2 Press the OUTPUT button to play the sound over the headphones only. 1 OUTPUT TV/ VCR RDS TEST TONE DOLBY/DTS SURROUND 0 PTY SPEAKER +10 RT OUTPUT SURROUND DSP SIMU. 5CH / 7CH STEREO 2 NOTE: To prevent hearing loss, do not raise the volume level excessively when using headphones. • The output to the speaker and pre-out jacks is turned off and no sound is produced from the speakers. Caution: Switching off the power of the unit and the unit will cancel the settings. [3] Turning the sound off temporarily (MUTING) 1 Use this to turn off the audio output temporarily. MUTING Press the MUTING button. Cancelling MUTING mode. (Remote control unit) Press the MUTING button again. TUNING + + SKIP ENTER - SKIP SHIFT MUTING - TUNER PHONO CD 1 1 2 3 24