Denon AVR-3808CI Owners Manual - English - Page 12

Checking the SIRIUS Signal Strength, and Radio ID, Listening to Preset Channels, Presetting Radio

Get Denon AVR-3808CI PDF manuals and user guides
UPC - 081757507646
View all Denon AVR-3808CI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

GUI Menu Map Setup Playback Information Troubleshooting ENGLISH Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit Button only on the main unit Button only on the remote control unit BUTTON [BUTTON] uio p [A ~ G] [ENTER] [SEARCH] [CHANNEL + -] [NUMBER] [SOURCE SELECT] [ TU] ( mode) [ ] [MEMO] uio p [SAT TU] (AMP mode) Checking the SIRIUS Signal Strength and Radio ID 1 Either turn or press [SAT TU] to select "SIRIUS". b When operating via the remote control unit, you cannot select SIRIUS even by pressing [SOURCE SELECT] to which SIRIUS has been assigned. 2 Press until "SIGNAL" appears on the display. The display will switch as shown below, depending on the reception conditions. Display EXCELLENT GOOD WEAK NO SIGNAL Status Signal strength is excellent Signal strength is good Signal strength is weak No signal 3 Adjust the position of the antenna until "SIGNAL: EXCELLENT" is shown on the display. 4 Press until the channel (example: "SR001") is displayed. 5 Press [ ] and select channel 0 (SR000). Channel No. and Sirius ID are alternately shown on the display. SR000 SiriusID Sirius ID b Write your own SIRIUS ID for storage use. Sirius ID : Presetting Radio Channels (Preset Memory) Your favorite broadcast channels can be preset so that you can tune them in easily. Up to 56 channels can be preset. 1 Tune in the broadcast channel you want to preset. 2 Press [MEMO]. 3 Press [A ~ G] to select the block in which the channel is to be preset. 4 Press [CHANNEL + -] or [NUMBER (1 ~ 8)] to select the preset number. 5 Press [MEMO] again to complete the setting. To preset other channels, repeat steps 1 to 5. NOTE Preset channels are erased by overwriting them. Listening to Preset Channels Operation on the Main Unit Press , then turn to select the preset channel. The strength of both the SIRIUS satellite and terrestrial signals can be checked at GUI menu "Source Select" - "SIRIUS" - "Antenna Aiming" (vpage 6). Operation on the Main Remote control Unit 1 Press [CHANNEL + -]. A pop-up window appears. 2 Select a preset channel using [CHANNEL + -]. 3 Press [ENTER]. Selection is still possible if you press [0 ~ 8] after pressing [A ~ G]. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
±±
GUI Menu Map
Setup
Information
Troubleshooting
ENGLISH
<STATUS>
uiop
<SOURCE SELECT>
<TUNING PRESET>
[
TU]
[MEMO]
uiop
[A ~ G]
[ENTER]
[CHANNEL + –]
[SEARCH]
[NUMBER]
[SOURCE SELECT]
[SAT TU]
Button located on both the main unit
and the remote control unit
BUTTON
Button only on the main unit
<BUTTON>
Button only on the remote control unit
[BUTTON]
Symbols used to indicate buttons in this manual
The strength of both the SIRIUS satellite and terrestrial signals can
be checked at GUI menu “Source Select” – “SIRIUS” – “Antenna
Aiming” (
v
page 6).
Checking the SIRIUS Signal Strength
and Radio ID
1
Either turn
<SOURCE SELECT>
or press
[SAT TU]
to
select “SIRIUS”.
b
When operating via the remote control unit, you cannot select
SIRIUS even by pressing
[SOURCE SELECT]
to which SIRIUS has
been assigned.
2
Press
<STATUS>
until “SIGNAL” appears on the
display.
The display will switch as shown below, depending on the
reception conditions.
Display
Status
EXCELLENT
Signal strength is excellent
GOOD
Signal strength is good
WEAK
Signal strength is weak
NO SIGNAL
No signal
3
Adjust the position of the antenna until “SIGNAL:
EXCELLENT” is shown on the display.
4
Press
<STATUS>
until
the
channel
(example:
“SR001”) is displayed.
5
Press
[
]
and select channel 0 (SR000).
Channel No. and Sirius ID are alternately shown on the display.
SR000 SiriusID
************
b
Write your own SIRIUS ID for storage use.
Sirius ID :
Sirius ID
Listening to Preset Channels
1
Press
[CHANNEL + –]
.
A pop-up window appears.
2
Select a preset channel using
[CHANNEL + –]
.
3
Press
[ENTER]
.
Operation on the Main Remote control Unit
Operation on the Main Unit
Press
<TUNING PRESET>
, then turn
<SOURCE SELECT>
to select the preset channel.
To preset other channels, repeat steps 1 to 5.
NOTE
Preset channels are erased by overwriting them.
Presetting Radio Channels
(Preset Memory)
Your favorite broadcast channels can be preset so that you can
tune them in easily. Up to 56 channels can be preset.
1
Tune in the broadcast channel you want to preset.
2
Press
[MEMO]
.
3
Press
[A ~ G]
to select the block in which the channel
is to be preset.
4
Press
[CHANNEL + –]
or
[NUMBER (1 ~ 8)]
to select
the preset number.
5
Press
[MEMO]
again to complete the setting.
Selection is still possible if you press
[0 ~ 8]
after pressing
[A ~ G]
.
Playback
(AMP mode)
[
]
(
mode)
<Illustration : AVR-4308>