Denon DN-A7100 User Guide - Page 27

Circle Surround, Parameter, Pro Logic, Music Parameter, 1 Ch Input Level

Page 27 highlights

5 PL II (PRO LOGIC II) MUSIC PARAMETER Pro Logic II-Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs. In this mode, DN-A7100 includes three controls to fine-tune the soundfield as follows. 5 PL II MUSIC PARAMETER PARAMETER : DEFAULT PANORAMAA : OFF DIMENSION : 3 CENTER WIDTH : 3 MAIN EXIT Select "PL II MUSIC" in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. PARAMETER: Select "DEFAULT" or "CUSTOM" with the 1 or 2 cursor buttons. If you select "CUSTOM", you can adjust three parameters as listed below. PANORAMA: Select the Panorama mode On or Off with the 1 or 2 cursor buttons. Panorama wraps the sound of the front left and right speakers around you, for an exciting perspective. DIMENSION: Set the Dimension level between +3 and -3 level in 1 level intervals with the 1 or 2 cursor buttons. Adjust the soundfield either towards the front or towards the rear. This can be useful to help achieve a more suitable balance from all the speakers with certain recordings. CENTER WIDTH: Set the Center width level between 0 and 7 in 1 level intervals with the 1 or 2 cursor buttons. Center Width allows you to gradually spread the center channel sound into the front left and right speakers. At its widest setting, all the sound from the center is mixed into the left and right. This control may help achieve a more spacious sound or a better blend for the front image. If "NONE" was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear. After you complete this portion of the set up, move cursor to "MAIN" with the 3 or 4 cursor buttons and press the ENTER button. 6 CS II (CIRCLE SURROUND II) PARAMETER 6 CS II PARAMETER TRUBASS SRS DIALOG : 0 : 0 MAIN EXIT 1. Select "CS II" in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. 2. To Select desired contents as below, press the 3 or 4 cursor buttons. TRUBASS: Set the TRUBASS level between 0 and 6 level in 1 level interval with the 1 or 2 cursor buttons. TRUBASS produced by the speakers are an octave below the actual physical capabilities of the speakers adding exciting, deeper bass effects. SRS DIALOG: Set the SRS DIALOG level between 0 and 6 in 1 level intervals with the 1 or 2 cursor buttons. This can be popped out of the surround audio effects, allowing the listener to easily discern what the actors say. If "NONE" was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear. After you complete this portion of the set up, move cursor to "MAIN" with the 3 or 4 cursor buttons and press the ENTER button. 7 7.1 CH INPUT LEVEL This sub-menu is to adjust the speaker levels for 7.1channel input sources. Here you will adjust the volume for each channel so that they are all heard by the listener at the same level. 7 7.1 CH. INPUT LEVEL VIDEO-IN : LAST FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN EXIT 1. Select "7.1CH INPUT" in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. 2. To select "VIDEO IN", press 3 or 4 cursor button. 3. Using the 1 or 2 cursor buttons, select the video input source which is emitted from Monitor out in the 7.1 CH INPUT function. The input source is switched by pressing the 1 or 2 cursor buttons as follows; LAST ↔ TV ↔ DVD ↔ VCR1 ↔ DSS ↔ AUX1 ↔ V-OFF ↔ LAST ↔ Notes: • When select LAST, the source is set previous source before 7.1 CH INPUT function is activated. • When select V-OFF, no signal is emitted from monitor out terminal. 4. To Select desired channel , press the 3 or 4 cursor buttons. 5. Using the 1 or 2 cursor buttons, adjust the volume level of each channel. 6. After you complete this portion of the set up, move the cursor to "MAIN" with the 3 or 4 cursor buttons and press the ENTER button. Notes: • These settings will be memorized to 7.1CH INPUT source. • This feature can be directly selected with the CH-SEL button of the remote controller. 23 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

23
ENGLISH
6
CS
II
(CIRCLE SURROUND
II
) PARAMETER
6 CS II PARAMETER
TRUBASS
: 0
SRS DIALOG
: 0
MAIN
EXIT
1.
Select “
CS
II
” in the SETUP MAIN MENU
with the
3
or
4
cursor buttons, and press the
ENTER
button.
2.
To Select desired contents as below, press the
3
or
4
cursor buttons.
TRUBASS:
Set the TRUBASS level between 0 and 6 level in 1
level interval with the
1
or
2
cursor buttons.
TRUBASS produced by the speakers are an octave
below the actual physical capabilities of the speakers
adding exciting, deeper bass effects.
SRS DIALOG:
Set the SRS DIALOG level between 0 and 6 in 1
level intervals with the
1
or
2
cursor buttons.
This can be popped out of the surround audio
effects, allowing the listener to easily discern what
the actors say.
If “
NONE
” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to “
MAIN
” with the
3
or
4
cursor buttons and
press the
ENTER
button.
5
PL
II
(PRO LOGIC
II
)
MUSIC PARAMETER
Pro Logic
II
-Music mode creates a rich and enveloping
surround ambience from stereo sources such as
CDs.
In this mode, DN-A7100 includes three controls to
fine-tune the soundfield as follows.
5 PL II MUSIC PARAMETER
PARAMETER
: DEFAULT
PANORAMAA
: OFF
DIMENSION
:
3
CENTER WIDTH :
3
MAIN
EXIT
Select “
PL
II
MUSIC
” in the SETUP MAIN MENU
with the
3
or
4
cursor buttons, and press the
ENTER
button.
PARAMETER:
Select “
DEFAULT
” or “
CUSTOM
” with the
1
or
2
cursor buttons.
If you select “
CUSTOM
”, you can adjust three
parameters as listed below.
PANORAMA:
Select the Panorama mode On or Off with the
1
or
2
cursor buttons.
Panorama wraps the sound of the front left and right
speakers around you, for an exciting perspective.
DIMENSION:
Set the Dimension level between +3 and –3 level
in 1 level intervals with the
1
or
2
cursor buttons.
Adjust the soundfield either towards the front or
towards the rear.
This can be useful to help achieve a more
suitable balance from all the speakers with certain
recordings.
CENTER WIDTH:
Set the Center width level between 0 and 7 in 1
level intervals with the
1
or
2
cursor buttons.
Center Width allows you to gradually spread the
center channel sound into the front left and right
speakers.
At its widest setting, all the sound from the center
is mixed into the left and right.
This control may help achieve a more spacious
sound or a better blend for the front image.
If “
NONE
” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to “
MAIN
” with the
3
or
4
cursor buttons and
press the
ENTER
button.
7
7.1 CH INPUT LEVEL
This sub-menu is to adjust the speaker levels for 7.1-
channel input sources.
Here you will adjust the volume for each channel so
that they are all heard by the listener at the same
level.
7 7.1 CH. INPUT LEVEL
VIDEO-IN
:
LAST
FRONT L
:
0 dB
CENTER
:
0 dB
FRONT R
:
0 dB
SURR.R
:
0 dB
SURR.B R
:
0 dB
SURR.B L
:
0 dB
SURR.L
:
0 dB
SUB W
:
0 dB
MAIN
EXIT
1.
Select “
7.1CH INPUT
” in the SETUP MAIN
MENU with the
3
or
4
cursor buttons, and
press the
ENTER
button.
2.
To select “
VIDEO IN
”, press
3
or
4
cursor
button.
3.
Using the
1
or
2
cursor buttons, select the
video input source which is emitted from
Monitor out in the 7.1 CH INPUT function.
The input source is switched by pressing the
1
or
2
cursor buttons as follows;
LAST
TV
DVD
VCR1
DSS
AUX1
V-OFF
LAST
Notes:
When select LAST, the source is set previous source
before 7.1 CH INPUT function
is activated.
When select V-OFF, no signal is emitted from monitor
out terminal.
4.
To Select desired channel , press the
3
or
4
cursor buttons.
5.
Using the
1
or
2
cursor buttons, adjust the
volume level of each channel.
6.
After you complete this portion of the set up,
move the cursor to “
MAIN
” with the
3
or
4
cursor buttons and press the
ENTER
button.
Notes:
These settings will be memorized to 7.1CH INPUT
source.
• This feature can be directly selected with the
CH-SEL
button of the remote controller.