Denon DVD 1920 Owners Manual - Page 16

DISC PLAYBACK Basic Playback DVD-V DVD-A CD MP3 Super Audio CD JPEG WMA Getting started • Turn on the power of the TV, amplifier and any other components which are connected to the DVD player. • Make sure the TV and audio receiver (commercially available) are set to the correct channel. 1 Press the POWER ON button. • "P-ON" will appear briefly on the display panel. 2 Press the OPEN/CLOSE button to open disc loading tray. 3 Place the disc in the tray, with the label facing up. 4 Press the PLAY button. • The tray will close automatically, then playback will start from the first chapter or track of the disc. If the playback does not start automatically, press the PLAY button. • When you play back the DVD with a title menu, it may appear on the screen. In this case, refer to "Title menu". 5 Press the STOP button to stop playback. NOTES: • A "prohibited icon" may appear at the top-right corner on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD player or the disc. • With DVDs that use some titles for playback program signals, playback may start from the second title, or it may skip these titles. • During the playback of two layered disc, pictures may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction. • The operation may vary when you play back DVDs with disc menu. Refer to the manual accompanying the disc for details. HDMI Setup 1 Press the HDMI button on the front panel to select the HDMI output mode. The output mode changes as follows every time the HDMI button is pressed. • The HDMI indicator on the front panel lights up when HDMI output mode is on. • Actual output signals for each HDMI mode are differ with the compatibility of the connected display device. Refer to the table on page 10 for details of output patterns of each HDMI mode. Pure Direct Mode 1 Press the PURE DIRECT button on the front panel to output an analog audio signal only (no analog video and HDMI signals will be output and the display will be turned off). The higher quality sound will be achieved. NOTES: • When pressed the buttons below, the pure direct mode will be released. OPEN/CLOSE button (on both the remote and the front panel), SETUP or DISPLAY button (on the remote), ON/STANDBY or PURE DIRECT button (on the front panel). • The PURE DIRECT button will not function while displaying the setup menu. • If you turn on the pure direct mode while selecting HDMI mode, both video and audio signals will not be output. Brightness of the Front Panel Display 1 Press the DIMMER button on the front panel to select the desired brightness of the front panel display. (BRIGHT, DIMMER or OFF) • The default setting is BRIGHT. NOTES: • The brightness of the front panel display can be adjusted from the setup menu. Details are on page 28. • When you turn on the power next time, the brightness of the front panel display will be as set in setup menu. General Features DVD-V DVD-A DVD may contain menus to navigate the disc and access special features. Press the appropriate Numeric buttons or use the Cursor buttons (K / L/ s / B) to highlight your selection in the DVD main menu and press the ENTER button to confirm. NOTE: • Unless otherwise stated, all operations described in this manual are based on remote control use. Some operations can be carried out using the menu bar on the TV screen. Disc Menus OFF 480P 720P 1080 DVD-V 1 Press the MENU button. • The DVD main menu will appear. OFF (Default): No video output from the HDMI OUT connector. 480P: Video output from the HDMI OUT jack at 480p. 720P: Video output from the HDMI OUT jack at 720p. 2 If the feature is not available, symbol may appear on the TV screen. 3 If disc menu is available on the disc, audio lan- 1080: Video output from the HDMI OUT jack at 1080i. guage, subtitle options, chapters for the title and NOTES: other options will appear for selection. • Video and audio signals may distorted temporarily 4 Press the Cursor buttons (K / L/ s / B) to select an when switching to/from the HDMI output mode. item, and the ENTER button to confirm the selection. • Use a display equipment with an HDMI-compatible port. • Progressive video signal will not be output from the COM- Title Menu PONENT VIDEO OUT during the HDMI output mode. • The HDMI indicator on the front panel flashes when you DVD-V DVD-A select the HDMI output mode but there is no HDMI cable. • If you turn on the pure direct mode, both video and 1 Press the TOP MENU button. audio signals thru the HDMI output will be cut off (press • The title menu will appear. the PURE DIRECT button again to recover). 2 If the feature is not available, symbol may • You can check the HDMI connection status by pressing appear on the TV screen. the DISPLAY button during playback with the HDMI 3 Press the Cursor buttons (K / L/ s / B) to select an output mode (refer to page 22). • If the TV is not compatible with newly selected HDMI output mode, the actual output mode will be kept the item, and the ENTER button to confirm the selection. • Playback will begin at the selected title. one before changing the selection. When this occurs, the newly selected mode will appear on the front panel display (see page 10) while the actual output resolution will be indicated by performing the on-screen display as described on page 22. - 16 - EN